HandAll Beavertail Rubber Grip Sleeve for Glock 19, 23, 32, 38

I bought this for my PSA Dagger that I have installed in a CAA MCK2. This product was very easy to install and has the desired feel that I completely expected from Hogue. It fits tight, is very durable and looks nice. It adds bulk to the size of your grip so if your grip is already too big for your hands then you probably wont care fro the addition.

Perfect fit, not too difficult to install. Great value and quality.

I can confirm that this perfectly fits the Shadow Systems MR920 Elite with magwell and "high" backstrap attachments. My hands are a bit too big (long) for the gun as shipped, causing my accuracy to be all over the place. Putting this grip sleeve on it got me back to comparable accuracy with my larger-gripped Glock 17 Gen 3. The sleeve added noticeable thickness/circumference to the grip, which made a huge difference. Note that I had to remove the magwell attachment to get the sleeve on, and the instructions did not work for me with this gun. Don't bother with cutting out plastic "shoe horns" at all. Just thoroughly heat the grip in almost boiling water, spray Windex inside the sleeve and on the gun grip, and (contrary to the instructions) slip the sleeve over the front of the grip first, then force the sleeve up onto the back of the grip. It took me about 3-5 minutes to get it fully installed. I have an FDE gun, and the FDE grip seems to be a pretty much perfect color match. I think it looks really good once installed, and it feels great to hold the gun now (much better than before). It seems like it will be very durable over the long haul (just 50 rounds fired with it thus far), but only time will tell.

G-19 Gen 5. I have thick calloused hands. Gripping any plastic gun grip has the felt effect of plastic on plastic. The Hogue 17050 HandAll Beavertail Grip Sleeve remedied all of that and more! Your strong hand gets a positive, non slip grip as well as a small bulge located between the palm meat and fingers that fills that void nicely to give your hand full contact with the grip. Your support hand gets a nice grippy area to smash your palm against for superior control. This grip makes the Glocks square grip feel more rounded with a smoother contour. The finger grooves are very stable and only get soft towards the very tips, this allows fingers of different sizes to fit comfortably without any hard edges. I find the finger grooves help settle my top finger against the finger guard thus allowing for the highest grip possible. The durability has been excellent with no noticeable wear. The grip stays clear of the magazine release and has not moved since installation with 100's of draws from holster. If you hate the front grip cutout on Gen 5's, you'll be happy to know that this grip will cover it but still allow it to function as designed for removing magazines. Installation was straight forward and easy. Place Hogue grip in very hot water for about 30 seconds, spray entire gun grip liberally with windex and proceed to apply Houge grip quickly before the rubber cools, make sure everything is centered and lined up and allow a couple of hours to set and dry. I was concerned that the beaver tail extension would roll or eventually gap, this has not occurred and stays very tight to the grip. The only issue that I ran into turned out to be a blessing. When I would draw IWB, I would draw with my thumb straight down, sliding my thumb along the smooth Glock plastic grip and my skin. The hogue grip is so grippy that my thumb would get hung up. I switched to a draw where I grip with my fingers and ride my thumb straight up the grip and hook my thumb over the top of the gun and the rear site ( most instructors teach this method for appendix IWB draw ). Once the gun clears the holster, your thumb slides down naturally into place. As a side note, I found that this type of draw to be far superior and allowed me to have the highest possible grip when executed.

Item as described, seller was great. Installed The Hogue Grip on my Glock 19 using hair spray on the inside of the grip, I put grip on the pistol with no issues.

Just in case anyone wants to know, this one fits on the S&W FPC.

The Hogue Handall Grip is hard to install but worth the effort. If you have extra large hands, this grip will make holding your Glock 19 more comfortable and more natural. Also, it makes the finger groves on my Glock 19 Gen 3 make sense. After getting my Glock 19 Gen 3, I understood why many reviewers had disparaged the finger grooves. Without the Hogue Handall Grip, the finger grooves felt vaguely helpful and mildly uncomfortable, but the grip enhances the grooves, helping me to get a more secure grip on the pistol. Yes, as other reviews mention, the grip is tough to get on, no matter the technique used. I tried all of them, from using hot water, using cut pieces of the plastic packaging, using a hair dryer, using 99-cent store Windex, and using a spoon. In the end, what worked for me was softening the grip in boiling water, placing the handle end of a spoon inside the groove side of the grip, and getting the back strap side on enough that I could use the spoon to stretch the groove end past the magwell opening, then spraying Faux Windex on the spoon and rubber grip which made it easier to slide the grip down the spoon handle past the finger groves, then spraying Faux Windex on the back strap side and sliding that side in place. I had previously tried all the other techniques while putting a Handall Grip on my Glock 26. After an hour of failure, I got the above process to work. My Glock 19 install took 15mins, including the 10mins to microwave the water.

Nice comfortable grip, Quality made. Little tough to get on. Looks nice

さわり心地がとてもよく、また太過ぎず手が小さくても持ちやすいので気に入りました。 裂けたとか書かれていますが、海外レビューに書かれている方法を実践したら普通に付きました。 まず2,3分湯煎し、そのあと説明書どおりパッケージをカットして靴べら的なものを作ります。(1個でいい) 作った靴べら的なものをグリップ前縁に当てて、内側にシリコンスプレーを吹いてからラバーグリップのビーバーテイル側を先に入れておき、靴べらを使ってラバーグリップの口をグリップに入れます。(このとき力が掛かるので、靴べら的なものの端が尖りすぎてると裂ける?) あとは熱いうちにグイグイ上に上げていけば普通に付きます。 英語レビューに失敗例も成功例も載っているので、届く前に読んでおくと良いと思います。

Fit my glock perfectly thanks

Nice grip

Fits well.

Fits the 48 like a glove