Water Level Indicator with Alarm on Tank FULL (with 5 sensors)

Ok, to begin with the product itself Is very useful specially if you are living at the ground floor or the tank is not visually accessible very easily so this can make your life much simpler. Keep in mind a few point before purchasing the product : 1. The main unit is actually small which is good because it looks quite big in the photos. 2. The wires in the sensors are of good quality so there is no issue in splicing the wire you can do it with a sharp knife and the insulation will slice right off. Some of you may think that the sensor will shock you or pass current in the water but its totally safe as its very very low voltage (SENSORS, NOT THE MAIN UNIT). 3. You may need to purchase some additional tools for this to get properly setup.( Like a small screw driver for the screws in the main unit). 4. If you don't make the connection strong they may break and you might think that the product is defective. If the sensor are working in the beginning and all the lights are turning on and later if they don't when you install it in the tank, that only means you made a mistake while installing . So make sure you seal the wire joints ( for extending the sensor) properly before you drop the sensor in your tank. 5. I used a pvc pipe to attach the sensor which I think was not necessary but I am hoping it will make the sensor work longer than average. 6. THIS IS VERY IMPORTANT POINT-You may be opting for a cat 5 or cat 6 cable for extending the sensor wires, now the wires inside the cable are not meant for this and they break very very easily if you move them around or bend them a little . So use bullet connectors or any wire jointers for this and save yourself sometime, also it will make sure the wires stay connected and don't break easily. 7 I have two tanks on the terrace and it did not make sense to purchase two sets of main units. So I just bought some extra sensor and attached the main units wire to ethernet rj45 connector (male /female) so I can just switch between the two tanks with a press of a button and check the water level. (You might need a few more tools and little knowledge of how ethernet cables work for this). 8. Test the connection at every step of the setup process. I completed the whole setup and taped everything just to realise that the 75% sensor was not properly connected with the cat cable. Had to undo the whole thing and do it all over again. The setup will take time and patience, it's better you do it yourself rather than asking a electrician or plumber because they won't invest as much time and dedication as you may do and ultimately one or more of your connections may break and they might say its a faulty product. Just installed the product and its working better than I expected. I am hoping it will work for atleast 2 years.

price looks too high ,i am using it from long time working as expected , given good instructions for installation , used cat6 wire for connection alarm is loud , strong body made of sheet metal, good bright led, , it should have beep/ melody sound rater continuous alarm, have mute button to avoid sound

I received the product today itself. Found it to be very well made. The indicator enclosure is made of metal sheet and not plastic, and hence, there are no chance of it getting burnt. It will remain cool because of heat transfer. Sufficient open space are provided on the sides so that SMPS / Adapter and the electronics remain cool. The AC wire is of 1.5 meter approx and well built which is a good length to connect to power socket. Five Sensors are provided - four of which are for water indicator and one is common. Sensor Wires are not flimsy - rather are of good quality. I connected it to my Water Tank which is on roof of 4th Floor through Finolex Cat6 Cable 15 meter which I purchased locally for Rs 20 per meter. I had to purchase one Electricity Plastic Box of 4"X3" to create junction box at the top of water tank where I joined all the Sensor Wires with Cat6 Cable through five tubelight connectors and placed .5 meter of extra wire in it for future repairs, if any. Made 1" hole at top of Water Tank and inserted all the connectors. I measured the total height of water at Full Level and found it to be 48" and hence I placed common sensor at 2" from Tank Ground, and other sensors at 12", 24" 36" and 48" from tank ground. Joined all the wires to the IPRO Indicator and found it functioning very well. When the Tank Water is full and touches the sensor at 48" lever, buzzer start, which has sufficient audio volume to be heard within a 25 meter range of home. The Switch given on the Indicator has three level - Buzzer On (indicator on), Indicator Off, and Buzzer Off (indicator on). I choose this Indicator over other models why: - 1. Wifi - triple cost, battery operated, Water tank unit has to be placed either over tank (sunlight damage or inside tank (water vapour damage & very less space inside water tank for such instrument); i doubted its efficiency over a period of time. 2. Fully automatic model to switch on motor - 4.5 time the cost, indicator for only Full Level, if pipe sensor malfunction - you will have burnt motor. Considering the cost involved - the fully automatic model must have at least four sensors to know how much water is left in the tank. 3. I wanted to know how much water is there in my tank so that i can use water appropriately, rather than auto switching the motor pump and not knowing how much water is there in the tank. I thank the Seller in taking care to send me Sensor Wires of appropriate length as per tank height of 1.5 meter as requested by me through Mobile Phone taken from Amazon Customer Car just after placing my Order

I brought this product on Feb’18 by amazon but installed it after 7-8 months of purchase as it was required wiring and setup which was delayed (having 3 floors) but it works only for 1 year after which it failed its performance. It was working fine but after 1 year this machine continuously showing one light constantly with the alarm when we press ON the power button and it hangs on that only I tried to contact customer service as well but I was unable to connect. The same purpose product is available under 150 INR but i brought this as it was looking little quality wise good but it works for only 1 year. My Electrition checked the wiring as well but their was the issue with the box only which he couldn’t figure out how to solve. Seller/Service please connect with me for my concerns

Look no further than the Water Level Indicator with Alarm, your ultimate solution to prevent water wastage and potential damage. Key Features: Advanced Sensor Technology: Equipped with cutting-edge sensors, this device provides precise and real-time water level readings. With five strategically placed sensors, it ensures accurate monitoring from empty to full. Clear Display: The indicator features a clear and intuitive display panel that shows the current water level at a glance. You'll always know exactly how much water is in your tank. Audible Alarm System: The standout feature of this device is its loud and distinct alarm that activates when the tank reaches full capacity. This ensures you're promptly alerted to take action and prevent overflow. Easy Installation: Designed for hassle-free setup, the indicator can be installed quickly on various types of water tanks, making it suitable for homes, farms, and industrial applications. Durable Build: Crafted from high-quality materials, the indicator is built to withstand diverse environmental conditions, ensuring long-term reliability and performance. Why Choose the Water Level Indicator with Alarm? Peace of Mind: Never worry about forgetting to check your tank or the risk of overflow. The alarm system ensures you're alerted in time to prevent any water-related accidents. Efficiency: Save time and effort with automatic monitoring. No more manual checks or guesswork about your water levels. Environmentally Conscious: By preventing overflow, you're contributing to water conservation efforts and reducing unnecessary wastage.

iPro Water Level Indicator I purchased from Amazon recently. After installation of the product I found that though the product is good, it is giving proper indication of level of water tank but the buzzer/ Alarm/ Sound is absolutely POOR. Hence the very purpose of buying iPro water level indicator FAILED. Because the alarm and sound quality is most important for this product. If you have switched on the submersible pump and you are busy doing some other job, it's the sound that will alert you to switch Off the pump at right time upon hearing the sound, which is missing in iPro. Moreover, considering its performance, this product is much OVER-PRICED. It doesn't deserve more than ₹400/-. Sorry BAD EXPERIENCE. I don't recommend this product.

Good product, value for money and reliable

It’s doing its job very well. Fitted to our over head tank. Very useful