Fully Automatic Water Level Controller & Indicator with Dry Run Protection 1 Year Warranty

Well, I bought this last year in December 2024 and now it's may 2025 Using it from the last 6 months So , it does the job I don't have to wake up every morning at 5 AM to come down from the second floor and turn on the water pump . The controller does it for me It's easy to assemble as per your needs from the manual provided or you can watch on YouTube, no need of an electrician The stainless steel sensors are also good , Customer service is responsive You can mail them or text them on WhatsApp Overall, great product Go for it

The product is great and works perfectly fine. Can be easily installed with the help of an experienced electrician. One thing to note is this product has push start button so once you push the green button the auto mode starts, issue is of there is power cut then you will have to again push the green button to turn on the auto mode. So of you are having frequent power cuts I would suggest go for a product with a switch type on button. Also for installation additional cost (significant cost) of wire needs to be considered so please think of total cost before buying.

---------------------------------------------------------- Here's how I tested the device prior to installation ---------------------------------------------------------- For this I used: 1. A electricity tester (screw-driver type) 2. Small (roughly 6-inch) pieces of wire (3 nos) 3. Electricity cable/wire with plug for 220v power supply to this device Procedure: Connect the 220v supply to the device (take care of polarity - 'P' is positive). Set device switch to 'Auto'. A: Inserted one of the small wires into the Sensor socket and the other end of it into the G socket. Next, switched on the power supply. This is as if the top tank is empty and bottom tank has water. The device worked properly as the 'G' LED come on (indicating there is water in the ground tank) and the 'motor on ' LED come on. I verified that power is being supplied to the output using the tester. See my photo titled 'A' B. With the power supply still on, disconnected the connection between the sensor and 'G' socket. This is as if the lower tank has become empty. The 'G' led switched off (indicating no water in the ground tank) and at the same time, the green 'motor on' led light also switched off. Verified with tester that there is no power output. See my photo titled 'B' C. Switched off power supply, reconnected sensor wire with 'G' socket, and added another small piece of wire into the sensor socket and other end into G1 socket. Switched on power. This simulates that lower tank has water and upper tank has water. The motor on LED went off. Verified with tester that there is no output to the motor. See my photo titled 'C' D. With the power supply still on, disconnected the connection between the sensor and 'G1' socket. This is as if the upper tank has become empty. The 'G1' led switched off (indicating no water in the upper tank) and at the same time, the green 'motor on' led light lit up indicating motor has switched on. Verified with tester that output socket has power supply. See my photo titled 'D' E. Continuing from procedure 'D' above, reconnected sensor wire with 'G1' socket. G1 led lit up and motor-on LED light stayed on. Now added another small piece of wire into the sensor socket and other end into B1 socket. This simulates that lower tank has water and upper tank is now full. The motor on LED should switched off. Verified with tester that output socket has no power. See my photo titled 'E' F. Continuing from procedure 'E' above, set device switch to 'Manual'. Pressed green button. The motor on LED lit up and verified with tester that output socket has power. Pressed red button and motor on LED switched off. Verified with tester that output socket has no power. Notes: 1. The sensor tips that were provided are just stainless steel bolts into which you connect the wire. I did not want pieces of plastic inside my water tanks so I removed the plastic covers, connected the wires and placed the SS bolts into the water tank. 2 Place sensor 'R' at bottom of lower tank. 3. The gap between sensor 'R' and sensor 'G' in the ground tank should be LESS THAN 1 foot (otherwise the motor will stop even though there is water in lower tank). Important: I bought two small packets of M-Seal and after connecting the wires to the bolts, I completely covered the top of the bolt (including the screws) with M-Seal. (See my photo titled 'F') This is so wire tips inside the SS bolt remain dry and does not oxidize due to moisture otherwise it will not only contaminate the water but sensor will also lose conductivity and device will stop working. So far, everything works fine and hopefully this device will last long. Thanks for reading and hope this helped you.

Product is good but the sensor get Salt coating after 1 to 2 months better use flotter senser

Further update after 5 months or use: The product malfunctioned, one of the sensor terminals (Lower tank pin B) is not responding. Sensors are wired correctly, and even direct shorting of pin B (lower tank start pin) to common R terminal does not change the status of LED B (always off). The pump will no longer auto start in this condition. Only manual control is possible. Seller does not respond to phone calls on given phone number, does not communicate on official Amazon message system and only provides WhatsApp communication so that no record is maintained in the Amazon message system. On WhatsApp, they are asking me to ship the defective product (which is within warranty) via courier to them in Gujarat for repairs. No longer responding to any further WhatsApp messages also. Extremenly poor service. If you buy this product, you are on your own. The warranty is effectively useless and had no meaning. Update after a few days: The sensors are unreliable, the upper tank stop sensor light now refuses to come on when water reaches full tank level. Results in motor continuing to run and water overflowing. Repeated resets (power cycling the unit, switching to manual and back to auto and starting the motor manually) sometimes fix the problem, but it randomly occurs again. Forced me to install another tank full alarm and revert to manually switching off the pump. Effectively I now have a fancy box with 2 manual switches, which I can remove and go back to switching the pump on and off from a simple power switch. Will continue to try my luck before tossing it out, but not too hopeful. Dropping the rating to 1. Original review: Value for money product. Works as advertised. The sensors need some care when installing to get proper functioning. Need to wait and see what happens in a few months when corrosion sets in. There are some instances when the unit goes into a hung state if power fails and comes back. This is easily fixed by switching to manual mode and starting the pump once, then switching back to auto mode. Also the metal body finish could be better. The paint was chipped in a couple of places. The support line phone number went unanswered when I called. Overall, decent value for money and a functional product.

I brought this its on automatic only auto off function Why its not working for automatic on Reply me

Edit 6/jun/2020: Using it for almost an year now. No issues. Really good product. I have never until now reviewed a purchase, this is my first. I would say, the most satisfactory of all my purchases on amazon. I have been using it for a month now. Excellent product. Has made life easier in my home. Found the review by MIKI really useful. Just followed his/her instructions before installation. Before purchase, I was skeptical about the negative reviews. However, I found the testing, installation and usage really easy. Having read the review of somebody who mentioned that it needs to be restarted once in a while, I have used a main switch to this box (white switch on the right side in the picture I have attached). Only once did I actually had to turn the main switch off and switch back on to reset this box (even cellphones, laptops, computers, TVs / Set-top boxes also need to be restarted once in a while, so no worries. It is not a faulty product). Otherwise, it has been working flawlessly. Value for money, go for it. 1. 1 hp kirloskar motor 2. Sump to overhead tank is 3 floors. 3. Product installed on 1st floor 4. 40m of 3 cable 1mm wire used (see attached pic) 5. Used m-seal to cover up the exposed copper portion (after all installation and testing was done) to reduce corrosion as suggested by other users. 6. The videos on youtube about this product were very useful and helped me trust the product developers.

Amazing reliable Product