S SATC デカール除去用ホイール 10cm(4インチ) ピンストライプ 除去ツール 1パック リムーバーホイール パッドとアダプター付属 グラフィック除去ツール イレイザー ホイール デカールリムーバー 4インチ

Knowledge is EVERYTHING. I used this wheel to remove the adhesive stuck to the paint on my truck that was left after removing the body side moulding. Use a heat gun to heat up the side moulding and it will peel right off. That’s the easy part. Learn to use this wheel properly and it will make your job of getting the adhesive off the paint very easy without damaging the paint. Important tip: it is not necessary to use a plastic scraper on the adhesive. It will do more harm than good. Don’t ask me how I know. I used this wheel with the supplied mandrel in my cordless drill. Getting a firm grip on your drill is important. The eraser wheel can chatter on the vehicle surface if you don't have a firm grip. I gripped the drill handle and trigger with my right hand to control the drill trigger speed, and then wrapped my left hand around the drill right behind the chuck. I then rested my right hand against the truck surface and used my left hand to push the wheel against the body panel. This is good form because my left hand controls the force pushing the wheel against the panel, while my left fingers are between the drill and the panel. This keeps the drill chuck from coming into contact with your paint. Turn the drill on high speed and try to keep the contact point of the wheel on the line of adhesive. Use medium pressure with the wheel against the panel. I now use my left hand to slightly move the wheel up and down while using my right hand to slowly push the drill left or right moving thru the line of adhesive. Take your time. After about going over 6 inches of the line of adhesive, stop and take a microfiber towel and rub HARD across the area you went over. The eraser wheel makes a huge mess. It is rubber and flakes off as it works. It will leave a thick tan residue on the paint. That is why it is necessary to have a high quality microfiber towel. It is best to use a short nap microfiber that you can see the individual nubs on the surface of the towel. Rub HARD with this towel to remove the tan residue left from the eraser wheel. This will not scratch your paint. Also know that the eraser wheel will get very hot. This why you don’t want to try to remove the whole line of adhesive all at one time. It needs to cool some. Know that the eraser wheel will smear the adhesive on the paint. That is why you want to keep the eraser wheel moving in an up and down motion as you use it, but don’t use a WIDE pattern because it smears the adhesive further. Some areas of the adhesive will be thicker than others, so it will require a second pass and possible a third pass. Always wipe the area with the microfiber after each pass to remove the residue left by the eraser wheel, otherwise the residue from the wheel keeps building up and you really aren’t getting down to the adhesive. IMPORTANT TIP: it is not necessary to use a wet cleaner or liquid adhesive remover of any kind while using the eraser wheel. If you do, you will only slow down the process. I thought I would be smart and use Goo Gone and 3M specialty adhesive remover after each pass of the eraser wheel after I had wiped off the tan residue left by the wheel. I thought this would further soften the adhesive and make it easier to remove. It did exactly the opposite. It also softened the eraser wheel and made it gummy. It smeared the adhesive more and made it harder to remove. AFTER you have made 2 – 3 passes with the eraser wheel and removed all the adhesive, then you can use goo gone to remove any residue left. Finally use a 50/50 isopropol alcohol/ water mix to remove all reside. I suggest you use a high quality automotive paint rubbing compound to remove any faint ghosting of the paint in the area where the adhesive was. Follow by polishing the entire door panel to blend and match the rest of the paint and then use a wax or sealer to protect the paint.

Machine speed must be moderate. High power machine may result in colour damage.

Worked very well for what I needed it for and it’s worth the price not too expensive

This little thing is amazing. So we just bought an ex work van that was full of sticker at some point. The company that sold us the van had done a decent job of removing the stickers, but there was plenty of residue still left on as well as what seemed to be expanding fome residue. This little thing took it off with ease. No chemicals and no damage. I personally ran my drill on the slowest gear and at gentle speed with light pressure added, use the side of the gadget and not the face of the gadget. Honestly follow my steps and you are good to go. This is a honest review and no promises or promotions have been added, this was bought with our own money.

I use the item to remove 3M tape that’s left over from wheel weights. It removed the sticky residue quickly and with a wipe of a rag and some brake cleaner the wheels is ready for more wheel weights. Does not scratch paint. Don’t go back and forth between using it on a rim then car paint. Pick one I guess 👍 good tool.