Premium Adhesive Copper Foil Tape - Double-Sided Conductive - 0.5 inch (12.7 mm) - EMI and RF Shielding, Paper Circuits, Electrical Repairs, Grounding, Arts and Crafts, Home Interior

Using this to make DIY capacitive touch pads for an ESP32/Arduino project (see photos showing wire soldered to a rectangular copper pad made from this tape and an adhesive copper pad stuck directly to the inside of a polycarbonate enclosure). Solders easily with standard multicore lead solder and the solder heat (using here 305 deg C) does not distort the copper or bubble the adhesive on the back with short periods of soldering - the heat quickly spreads evenly throughout the thermally conductive copper rather than melting the adhesive directly below. Works really well for soldering to and solder flows nicely on the copper surface. Adhesive on the back is strong and will reliably stick to polycarbonate project enclosure box sides without lifting or curling at the edges. Polycarbonate has a reasonably high surface energy and I would expect the tape to stick well to similarly high energy surfaces. An ideal low cost tape for RF shielding on projects or for making things like capacitive contact pads. Not too thin and holds its shape when you come to stick it to something. It may crease slightly when removed from the backing, particularly if mishandled, but is easily smoothed out when applying to get it looking flat again. Tests with continuity meter confirm the adhesive is conductive, I measured about half an ohm from front through to the adhesive back so you could layer and overlap multiple strips of tape inside an enclosure to provide shielding to all sides. Recommended.

Soo much better than using slug pellets. It's still on the planters outside and working well from last year. I put tape near the bottom of the pot (to save tape) but if you are feeling vindictive put it at the top. 🙃 I also cut the bottom out of the plastic pots that young plant were in, put tape around the top and planted them in the garden.

Very good product. Easy to apply and also to perl if needed. Conductivity very good. Used it for various repairs in desktop PCs, laptops and some creative electrical works. Highly recommended!

This tape works well for shielding guitar cavities. Easy to cut to shape and the backing paper peels off easily. The copper tape without the backing has a tendency to roll up and stick to itself so it takes a bit of practice. Sticks to surfaces really well - smoother surfaces best, but will stick to the rougher wood too. Also stick to pick guards well. Overlapping the tape gives good electrical continuity, so can be used to make bridged front and back cavity Farraday cage shielding for strats, etc. Have used it on a refurb of an 80s super-strat, and a traditional style "partscaster" build - works great on both. Seems to work quicker and better than the conductive paint stuff which is generally too much of a faff to bother with. Will use this stuff on all my builds going forward. Recommended.

I bought this because I thought it was double sided sticky tape that had conductive adhesive on copper foil. I was wrong. This is great value copper tape with very strong adhesive that is conductive but it is NOT double sided sticky as I thought.

I needed this copper strip to repair my rear screen heater connection on my car. I had been told that the only possible repair was buying a new rear screen. The copper strip has conductive glue on the back. 1 one inch strip, left to ensure the adhesive fixed on the contact area of the screen, and then I tinned it with solder, resolved the contact with a solder gun and two minutes later heater working fine. The solder gun is best because as soon as you release the trigger the heat dissipates to avoid cracking the glass of the screen. I have loads left for any other electrical repairs.

Most adhesive copper foil has the disadvantage that the adhesive is non-conductive; hence, sticking one piece on top of a broken track on a circuit board won't work, you would have to use conductive silver paint as well to get a connection. So I was highly skeptical about this product, given that it costs about the same as regular copper foil. I stuck two pieces together and my multimeter reports that they are in electrical contact. So this stuff does indeed work as advertised and will come in very useful.

A thin, very pliable (so you can get it in to nooks and crannies) self adhesive copper tape. My application was for making up some fully shielded dummy USB 3 plugs to stop some unused USB ports causing interference to a neighbouring 2.4GHz WiFi access point. Apparently it also repels snails although since they rarely bother trying to eat my access point I cannot vouch for this.

This copper foil tape has been a lifesaver for my electronics repairs! I recently used it to fix a loose connection in my game console, and it worked perfectly. The adhesive is super strong, and the tape is highly conductive. It's also easy to work with and conforms to different shapes. If you're into electronics repair or DIY projects, I'd definitely recommend this copper foil tape.

Aufgrund der negativen Rezensionen, das Kupferband wäre nicht beidseitig durchleitend, habe ich es direkt nach Lieferung geschnappt und mal mittels Multimeter von hinten zu vorne den Durchgangswiderstand gemessen und kann ganz klar bestätigen. Es hat 0 OHM !! Somit ist dieses Band wunderbar für jede Art von Fixierung im elektrotechnischen Bereich geeignet, an dem eine stromtechnische Verbindung gewünscht ist. Beispiel wäre ganz klar die Fixierung der Schirmdrähtchen eines CAT-Kabels beim Anschließen auf Keystone-Module, Patchpanels oder dem Montieren von Steckern. Das war zumindest mein Kaufgrund :) Dafür scheint es super geeignet und stellt mit die günstigste Alternative in diesem Bereich dar. JA, es ist etwas empfindlich und aus meiner Sicht ist es nicht optisch nicht 100% für gewollt sichtbare Verklebungen geeignet, da die Kanten doch schnell umknicken. Technisch gibt es aber überhaupt kein Grund zu meckern. und für den Preis kann man das defintiv kaufen ;)

Ik gebruik deze tape om antenne's te plakken op (auto)ruit. Laat zich ook geweldig goed solderen. Handig!

Good

Good