MUSETEX PC CASE ATX 6 PWM ARGB Fans Pre-Installed, Type-C Mid Tower Computer Case with Full-View Dual Tempered Glass, Gaming PC Case,Black(K2)

I love this case. I just completed an ATX build and it went great. The space inside is awesome. Lots of room I had to put my top fans down so I could install a water cooler no problems the 360 cooler went in on top without a hitch. I just put the the top fans directly down so they drew air in because my cooler rad pushes out. I turned my 2 side fans around so they pushed out as well. So a tip for fans is if you're looking at the concave side.....that's the side they push to. The rounded side is where they draw from. Anyway my build went great. Good cable management on the back. RGB for fans worked great. If you move your top fans down you have to rearrange the plugs. Just be careful what fans are plugged in to certain daisy chain. It looks great and functions very well. I ordered another one

Although I’m ashamed to admit it took me quite long to assemble everything, I will say that this case and the six included RGB fans are amazing and work great. They run quiet and everything inside the PC is nice and cool. The tempered glass is very durable and looks so good once you peel the satisfying plastic layer off (don’t leave fingerprints!!!). The included screws and manual help with installing and wiring the fans, and the wiring is mostly neat and already tucked away for you, all you have to do is hook it up to your motherboard! I could be biased because I got this case for $38 after using a coupon and a gift card but still for its base price I would hands down buy this again for my next build if I were to switch cases.. but I will probably stick with this one for quite some time because it looks so good. P.S. For those who are new like me and are concerned about compatibility, this case and a few of the other cases from MUSETEX are available to select on pcpartpicker.com and will make the build process so much easier!

I'm writing this review because I was very impressed for the price. This case would be good for AIO builds like shown in the pic, but out of the box isnt perfect. The air flow for traditional dual tower CPU cooler is even less ideal. The fans are actually good quality, daisy chained, and the 2 side fans are reversed fan blade fans, at this price point is amazing (Note: Reversed fans means ugly X-frame is on the opposite side of traditional fans). The problem is i cant find to buy a 3 pack of reversed blade fans to add to the PSU shroud vented bottom, which is shown in pic but empty in case. I know description say 6, but it should say 4 exhaust fans and 2 intake, and have an option to have 3 more intake (reversed fans), totaling 5 intake and 4 exhaust fans . Out of the box fan set up will make it a negative pressure system (vacuum air flow), which means dust accumulation thru all the cracks which is not desirable, you want to control intake air by having a positive air flow, coming only thru the proper air filtered paths. This could be solved by reducing the speeds of the 4 exhaust by approximately half the speed of the intake fans. Or negative pressure by adding more intake fans. Two problems with moving some exhaust fans down on the PSU shroud for intake or adding more rgb fans. First, is that you wont get reversed blade (at a decent price), which means you will see the ugly X-frame, maybe you dont care, but my pickiness about matching the other fans would bug me. The second problem could be more of a deal breaker. If you decide to add 3 bottom intake fans on the PSU shroud, the shroud cavity wasnt well planned to be a space to easily draw air from. Even thou can remove the HDD tray and add a 120mm fan in the "basement", only one is possible and the HDD tray vent doesnt have a filter, and is a rectangle (100-110mm x 50ish mm) instead of a 120mm round grill hole. So thats not good, there wouldndt be enough air flow to supply 3 fans above creating negative pressure basement cavity. Another side note: PSU bottom intake filter (in the basement, is one of those crappy flimsy square cuts in the mesh material without a finished edge types, held in with small side tabs on the case floor, the middle of the edge on all 4 sides, the terrible way to do it holding tabs. No magnet, not frame to pull out. To fix everything for a V2 by the manufacturer stop the shroud short, boxed in to hide PSU cables (no vent holes needed on shroud), add 2 intake fans to case floor for intake, permanently delete the HDD tray from basement, or integrate it on top of PSU shroud. Could have been a 5 star, almost a 4 star, i give it a 3.5 star, but if you like modding you could have that 5 star, maybe!

Simplify put, this is an incredibly good case for not a lot of money. There's plenty of room and cable management is a breeze. The build quality is apparent right out of the box. It's been almost a year since I built my system and just opened it up yesterday to vacuum the inside only to discover minimal dust inside. I'm so pleased with this case I plan to purchase another when I build my son's pc. 10/10 highly recommend.

This is the prettiest computer case I ever have. I usually only buy full ATX case to accommodate my many HDDs and DVD-ROM. But this year's upgrade made me realize I should leave most of these outdated devices in my old computer and just go for M2 SSD for fastest speed. This case is smaller than my previous case, but it is still able to hold two HDD and two SSD. The point is the looking is far superior than the old one. The RGB lights and the full glasses exterior look fabulous. All six pre-installed fans seem to do a good job to keep the pc cool even when playing games. The USBC connector on the front is fast when pairing with a USB4 cable. I would highly recommend this case to anyone who is upgrading PC and need a functional and great looking case.