3 Replacement Lids for Stainless Steel Tumbler Travel Cup, Leak and Spill resistant Lid for 30 OZ Rambler or Others of Insulated Mugs With an Inside Diameter of 3.7-3.74 Inches

My prior lid broke due to the slide top clips breaking. The lid works fine but with repeated cleanings the clips that hold the slide to the lid become brittle and break, far too fast. If you don't remove the slide it probably will last longer than mine have but if you drink coffee the lid and slide will need cleaning and that is detrimental to the tips. Works fine if the use is seldom and does not involve removal of the slide. I don't envision ordering these any more.

I bought these for my husbands tumbler and it’s the wrong size for a skinny 30oz tumbler but they do fit my yeti so all keep them

Just what was needed. The RTIC cooler lid didn't survive the drop. It's still my wife's preferred water jug due to its weight and construction. The replacement lids fit perfectly and allow her to keep using her favorite jug!

I have a generic 30 ounce SS tumbler that I have been using for years.. The plastic in the lid broke and needed replaced, so I checked to see what was available as a replacement.. I found 2 different styles that I liked (which are shown in my one picture).. This one was identical to my original, which is why I bought this as one of them.. So I will give a comparison to both of them, and my original one..Overall, this one is almost identical to the size and quality of my original lid.. With one exception.. The rubber seal around the edge does not fit as tight as my original one.. My original one had 2 flaps in the rubber to give it a better seal, while this one only has one.. To be fair, both designs, this one and the other one, both has the same 1 flap rubber seal.. So what did I do, I took the one off of my old cup, and put it on this one, and it fit 10 times better.. Simple fix..One of the reasons I tried 2 different types.. I use SS straws.. They come in 2 different diameters.. My mom likes the thinner one, I like the thicker one.. But not all lids will fit the larger diameter SS straw.. Luckily for me, both of these, the larger straw did fit.. Yea..So this lid is good, nice construction, but it does have a couple of flaws.. First being the flap to close it.. Since it goes through some holes to fit into a track in the main part of it, these are 2 holes that will allow stuff to spill out if it gets knocked over on the side.. The other design that I bought did not have this.. The second flaw.. Since the rubber is softer, and only one seal flap, if you drop the cup, and it is full, the lid will most likely come off.. Again, with mine, this was fixed by simply putting my old rubber seal on this new cap, which is why I am not complaining about it.The other cap that I bought, does have a silicone piece to cover up the straw hole to keep stuff from spilling as much too, where this one is just a hollow piece of plastic over it, which only restricts flow, not stop it..Since I do not knock my cup over a lot, nor do I drop it, I am not too worried about the lid being 100% sealed.. One positive note about the way that the slide part is on there with this one.. You can push on the parts under the cap to release the slide part, which makes it really nice for when you clean it.. Not sure about the other cap yet..

My other lid had cracked when I dropped it. This is exactly what I needed- does perfectly.

I was excited to get this new cover for my large thermal containers. I have YETI and other brands and these lids fit perfectly. After only using one lid on my YETI for three days, it broke. The sliding cover for the drink holes broke. The moving lid closure that fit really snug just broke on both sides at the same time. The sliding closure has a thin piece of plastic that fits in the groove that goes back and forth over the drinking hole. I slowly poured out my coffee and tiny bits of this red plastic were on the bottom of my YETI container. This is dangerous in my opinion.The fact that it broke after three days of use with my morning coffee just tells you how cheap/flimsy this design is. Don't waste your money on this. It is a dangerous design in my opinion.I ordered two lids from this vendor that were clear with a black clicking closure that moves back and forth to open and close. This black closure clicks when you move it back and forth. This lid broke the first time I used it for Coffee. The drink opening had a line break in the middle of the drink opening hole all the way through the plastic that went to the outer seal. This break happened within an hour of using it. The lid leaks now and it slides easily without clicking so it slides back and forth without touching it.Note: I had to add this review to the other review because you can not review each different lid this vendor offers separately. So far, these two different types of lids are JUNK from this vendor.I did buy another type of magnetic lid from this vendor. It actually works. I think I will pony up and buy the real Yeti lid of this magnetic type. I wanted to try these cheaper ones first to see if they might work without paying the high price for four Yeti lids. Now I know which lid really works well for Coffee.

I ordered wrong size. Wrong size lids but they are very nice and wonderful and . and I wish they had them for the 10 oz and 12 oz size

Did not fit my 20 ounce tumbler, it does fit my cup though so I will keep the one that wasn't broken. One of the lids arrived broken. Sucks that I still need a lid for my 20 oz tumbler.