Front & Rear Fender Flares Compatible with 2018-2024 Jeep Wrangler JL & JLU Unlimited Sahara, Installed on the Original Fender Flares(Not Fit High-Rise Flares, Not fit 4xe)

This product was packaged very well and arrived with rivets and screws needed for insulation. You do need a plastic rivet tool in order to complete the installation. I did not need to use a drill. I pried up a little on the rivet and used a tool to cut the rivet off. Installing the new rivets was very easy using a plastic rivet installation tool which you can buy separately for 17 or $18. Each Fender Flare is labeled very clearly as front or rear and left and right. I started the installation with the center most rivet and worked my way towards each of the edges of the fender flare. I had to hold the flare in place while I inserted the rivet but once I did everything matched up really well. There's very little gap between the fender flare and the original fender. It does look very nice and seems to be very good quality plastic. It seems very secure. Overall I'm very happy with this product and I expected to last a long time. Time will tell however if the plastic is of good enough quality so as not to discolor rapidly over time faster than the fenders do. I suspect using the same product I would use on the fenders to protect the plastic should work.

Put on a jeep e p rubicon. Fit great. Eady to install. Durability good . On jeep for about 6mth. Hole alignment a little off but easy corrected.

Installed these on my 2024 Gladiator Mojave to get some more coverage for my 35" tires on a -24 wheel. They fit great and work as intended. Great addition to my Jeep Build.

So far, these are perfect for my set up. Took about an hour to do all four, but make sure you have the right tools or it will take much longer. Looks nice, adds a rugged flair to the fenders and just about covers the tires. Off roading is a whole different test, hope they hold up!

I put these on a 2024 jeep wrangler Rubicon. At first out of the box I was a little worried, because I immediately, (based on past reviews of unaligned hole), held them next to my fender wells to see if the holes line up. Initially I thought they didn't as there are more holes in the new flare than native rivetsnin my fender. However, this became a good thing. The flares do have holes that line up perfectly, you just have extra holes in the new flares so that you can secure it more tight with the screws that comes with the kit. It actually brings it closer to the existing fender. A lot of people were complaining that the rivets were too small, I initially thought the same until I realized how to put them on properly, (use them properly), then they worked perfectly. The flares will act warped and not form fitting, but once you line up a bottom rivet in the correct hole and top hole, it will hold it in place, and when you put the rest of the rivets in, it probably molds secure in place on the fender. And again, the extra screws help you mold it even tighter. See pictures. I went from initially disappointed thinking I would have to return them, to extremely satisfied. It took me longer to be hesitant and figure things out than it did to actually put them on.

Great quality but a pain in a** to install and need extra tools. I think I ended up scratching my fenders more than what they would have saved from rocks. Hardest part was cutting off the excess rivet after you install them. There's no easy way of doing it without scratching it in some way. The bottom rivet for the rear fender extension does not want to grip all the way so make sure you pull it all together tight before riveting otherwise you'll be like me and go through 7 rivets until it finally catches. The fit is spot on and the quality is great, but DO NOT USE THE INCLUDED RIVETS. Find a different kind of fastener to secure them. Also best way to get factory rivets out is to drill it with a 7/16" bit and then pull it out. Found out the hard way after spending over an hour trying to remove them with different methods.

Items went on easy and look good.

OEM look and fit. Great packaging as well. I did not use the included rivets, but very pleased with the quality of the extensions. Simple installation and each piece is labled which corner it's for. Pretty easy to figure that out though lol, but I appreciate the attention to detail. Highly recommended.

Easy installation..make sure to use a rivet gun specifically for plastic rivets. Look great on vehicle and have optically reduced the sticking out of terrain tires

Estéticamente son muy geniales, y para los que ensanchamos las ruedas y sobre sale de la carrocería original, son muy funcionales para que no se ensucia en lluvias o charcos

Excellent product and fit. Easy install with a rivet tool.

Perfect fitment, easy to install. No need of plastic tool for the plastic rivots. I just used two pliers, one to hold the base & one to pull the rivot at the same time. Quick install in 20-30min.👍

These are perfect on jeep gladiator. Install was easy, no drilling, just plastic rivets that are supplied. Awesome!