Amico 12 Pack 4 Inch 5CCT Ultra-Thin LED Recessed Dimmable Can/Ceiling Light with Junction Box, 2700K/3000K/3500K/4000K/5000K Selectable, 11W Eqv 70W, 800LM High Brightness Wafer Downlight - ETL&FCC

These are lightweight, self-contained units that connect easily to existing wiring. I have used them to replace a number of ceiling-mounted lights. The very slim profile allows them to fit into drywall regardless of the space above, even if the former box was attached to a joist. As long as you have enough space to get the wiring housing into the space above the ceiling, these work beautifully. The light is also adjustable; I typically choose around 4000K for a nice clean "natural" light. Because these fit flush to the ceiling but don't "recess," the light also spreads much better than recessed can lights that often create a "cone" of light and resulting darker spots in a room. Steps are easy: (1) Cut power to the light; (2) remove the existing light fixture; (3) remove the gang box or other mounting (in some cases you can simply push it to the side) and prepare the wiring for the new light; (4) cut a 6" round hole for the new light; (5) attach the existing wiring into the housing for the new light (push fittings are very nice) and set this housing/box in the void above the ceiling; (6) use the spring clips to set the new light securely into the round hole. Even the most challenging installation took me only about 20 minutes in all.

Bought these to replace a couple dimmed recess light around the house. These lights arrive quickly and are quite well built, each with a junction box and pre-stripped lead wires as well as connectors if you don't have some already from previous installations. My old lights had cups behind the LED, and since they were above the attic without top access, I just took off the screw and poked them up to make space. The junction box fits easily into the original hole, and I like the design with two spring ears on the light, easy to install as well as to take off in case you need to adjust the light temperature like I did. So far it's been working like a charm, very steady and bright and looks better than the garbage installed by the builder. I plan to replace all ceiling light with these in a couple of weeks.

I bought these because they were about half the price of the home depot options and I wasn't sure if I liked how flush mounts look. I am completely blown away, these were a fantastic purchase and have completely transformed the rooms I put them in.Two-part design is thoughtful and makes installation super easy. Push connectors were included, and only takes about 5 minutes to wire each one including installing NM clamps on the knockouts. Sometimes on lower cost LEDs like this, the warm colors look unpleasant or don't match - not so here. All of the color options had great tone, selection was easy, and the dimming works down to the lowest ranges, no flickering or other issues.Big fan, I'll be buying again.

Easy install. Updated the bathroom lights. Very bright didn't need all of the lights I purchased. Excellent quality and buy.

I've installed a lot of lighting like this, so I'm definitely not new to the product nor the procedure. I've got to say that I'm a bit impressed with the quality of these -- they're comparable to what you might buy at the big-box home improvement chains in every way, but at a fraction of the cost.They were packaged very well, and not a single problem with any of them -- no crumpled gaskets, no twisted wires, no bent housings, no missing or broken parts. The installation experience was identical for each one, no troubles at all.More importantly, their performance is outstanding. The light throw is very thorough and even with absolutely no hot spots or shadows. And I am a bit impressed with their light output -- they're BRIGHT! And what I mean by that is they make more than enough light for their size, so it won't take many to evenly light a given space or room.The only complaint I have is on the diameter. They're Ø6.7", and they recommend cutting a 6.25" hole, leaving less than 1/4" of a lip for the light to hold onto. That leaves virtually no room for error, so if you plan to cut the hole by hand, be very, very, VERY careful that you undercut (and use a utility knife with a fresh blade rather than a keyhole saw). If you use a hole saw, the ones designed for 6" recessed lighting are usually 6-3/8", so you're in dangerous waters if you use one of those. In any case for drywall, if you somehow crumble or tear the edge of your hole, it WILL be visible when the light is installed.I used an adjustable hole saw (a Klein 53710), which could be adjusted in 1/4" increments, so I was able to cut the recommend size hole without any error, but it took a little effort to line up the light in the hole to make sure there were no visible gaps.Overall, this is an excellent buy. i can't speak on the longevity, of course, but given the overall quality and performance, I expect that these will last for many years.