Teexpert Crystal Clear Epoxy Resin Kit 1 Gallon Self-Leveling Coating and Casting Resin, High-Gloss & Bubbles Free Resin and Hardener Kit for DIY Art, Jewelry, Table Top, Molds, Wood 1:1 Ratio

Very good quality resin All my projects come out clear and it self bubbles unless you use a machine to mix it then you have to bubble it yourself with a torch or lighter or heat gun. It works well for big or small projects takes in colors very well sets in 24 hours it’s able to demold after 8 but I leave it be until 24 hours it’s not sticky if you wear gloves when it dries it’s solid it’s easy to clean with diaper wholes I found that the Amazon wipes are sturdy without tearing but I add hand sanitizer or water to the wholes for more moisture as needed to help absorb slipping resin10 outa 10 would recommend I use it over and over I think I’ve bought 12 gallons already from them

I absolutely love this resin and it is my go to resin for my resin products.The quality of the pieces are top notch. Its easy to use and creates less bubbles in the pieces. I had had peices for a long time and do not see yellowing that has happened in some other resins I've used.Its my go to and will continue to be. The price is definitely worth it.

I was about to quit playing with resin after going through way too much money and ruined products because of other resin types. Then I tried this one and "I'm back in business, baby!"It does need a bit of work, but the results have been a resin that release the bubbles better than anything else I've tried, so to my fellow newish resin enthusiast... Here's how I've had best success:1) Measure the needed amount of each into separate cups (I use reusable hard plastic ones with lids, so I have less trash waste) and place them in some warm (not hot) water for 3-6 minutes depending on the amount.2) Mix the A+B resin in a new cup. I use an electric resin mixer and it does have to be mixed a bit longer than other ones - really look for those stringy part in there!3) Place the cup back into the warm water for 3-5 minutes.4) Pour slowly and then use a toothpick or craft stick on the sides of your product to make sure no bubbles got stuck there. And remember, the deeper the project the harder a time bubbles have releasing, so work in layers if you must.5) Do your usual heat gun/lighter tricks, and voila, you'll *most likely* have a nice mostly bubble free result!One last thing... This is a lower viscosity resin and works great in molds, but I found that it really wants to fall over the sides when used as a top layer on coaster for example (even after a 15-20 minute work time), so you may want to use it as the bottom layer and then top coat it with a thicker working resin or wait long enough till it's thickening up a good bit itself.

Very good product for beginners and if you warm the two solutions separately the bubbles are little to none. It’s affordable.

***SECOND EDIT****THE SECOND BATCH THAT THE COMPANY SENT TO ME WORKED LIKE A CHARM. I AM GRATEFUL FOR THE REACH OUT - AND THE REPLACEMENT PRODUCT. I HAVE BEEN ABLE TO MAKE KEY RINGS, NECLACES, AND EARRINGS. I DECIDED TO USE THIS PRODUCT BECAUSE IHAVE HAD PROBLEMS WITH BUBBLES SITTING IN THE MOLDS, AS WELL AS CLOUDING MY CLEAR CASTS. FORTUNATLEY THIS LAST BATCH HAS NOT HAD THAT PROBLEM. ********COMPANY CONTACTED ME AND SENT ME REPLACEMENT BATCH. I HAVE NOT HAD A MOMENT TO USE THE NEW BATCH DUE TO OTHER CIRCUMSTANCES, HOWEVER THE COMPANY HAS FOLLOWED UP WITH ME ASKING FOR PHOTOS OF THE PROJECTS THAT DID NOT WORK TO SEND TO R&D. HOPEFULLY THIS NEXT BATCH WILL BE PERFET. WILL UPDATE REVIEW WHEN I AM ABLE TO TEST PRODUCT.***I loved the idea of the pump - for better accuracy in measuring the epoxy and hardener - I even bought two!NOTHING I mean NOTHING has set. I measured accurately, and even double checked my measurements after the first batch failed. I emailed the email address from the seller's information page and have yet to receive a response.This was referred by an influencer I follow on Youtube, and I feel he earnestly suggested this resin in good faith as I have followed his advice for over a year now.I thought that maybe my first batch was a bad batch, nope, opened the second batch I ordered and measuring extremely accurately, because of my results in the previous two pours. STILL did not set, everything is floppy. I hate to give bad reviews, because I understand how much reviews mean.I am just disappointed in the product - its results are different than the influencer was able to demonstrate.

The media could not be loaded. 1 gallon each bottle, easy pour and mixing is simple with 1 being A and the other being B of equal parts..I already used some and my molds came out great. I think this is a great price for gallon bottles

I have used many different brands from $250 a gallon epoxies two $49 a gallon poxes and this is the clearest hardest least amount of bubbles least amount of yellowing of any other brands I’ve used and I am switching to this 100%

Good epoxy but areas that are narrow never cure atiff