Rugged Ridge | Radio Mounting Bracket, CB | 11503.95 | Fits 2007-2018 Jeep Wrangler JK

Bought a Uniden PRO520XL CB radio on Amazon for my 2015 Jeep JKU, and was debating where to install it. This mount is a perfect location.I thought the installation would be simple, then got nervous when I realized that I would need to pop out a portion of the windshield trim. Turns out that the installation was simple. Remove freedom panels, gently pop out the trim just enough to access two bolts, and the rest is simple (printed instructions in the box do the job).The only (very minor) challenge was drilling two holes in the Uniden bracket to line up with the pre-drilled hole set in this bracket. I shared pictures.I also shared pictures of the wiring from the battery, through the firewall and up the trim. Cables not yet connected to battery (red/positive and black/ground). Antenna not yet installed, and coaxial not yet run, so no more pics to share.(Update 1)The other week there was torrential rain, blowing sideways. I have a hardtop on my 2015 Jeep Wrangler JKU. If you have a Jeep Wrangler, you know that water sometimes gets in through the seam on the freedom panels. My Jeep is no exception and I found some water dripping off the sides of the CB radio in the morning. I am fortunate that the vent on my CB is on the underside, and the water didn't get inside. If the vent was on the top or sides, it would likely have damaged the internal circuitry.

Exactly what was advertised works great.

Installed in a 2015 Jeep Wrangler Sport. The CB I am using is the Uniden PRO520XL Pro. While this is a smaller lightweight radio, I feel like this mount can hold triple the weight of the radio I am using. It is very well built, well painted, etc. I tested it on a bumpy trail behind my house and run-down road. I could not notice the mount bouncing at all.The mount took less than 10 minutes to install.This is the perfect location for the radio. It is well high enough away from the movement from the general cab area and any water exposure that might happen when mounted at seat and below level. I was able to route my power and antenna cables through the windshield plastic cover and pillars for a clean install. Very little wire exposure from back of the CB to the windshield cover.

The Rugged Ridge CB mount fits my 2017 wrangler sport 2 door just fine.Installation took about an hour. It requires removal of the three trim pieces around the windshield, as well as the retaining bracket for the sunroof. There is no drilling required, but you will need star bits to remove the retaining bracket.The mount itself is a little thinner than I would have chosen were I to manufacture it from scratch. While driving, my UV-50x2 vibrates and wiggles pretty strongly. It can be annoying, but I don't think the bracket will break. This could have been solved by using thicker steel.The mount itself is not inherently centered due to the placement of the sunroof retaining bracket. But this can be offset by mounting the CB retaining bracket to the side. Depending on your CB mounting bracket you may want to drill holes to adjust the left to right placement. My radio sits right above my rear mirror even though the main bracket is attached to the left of the mirror. My radio does not obstruct the mirror at all.The built in cable hook is a nice feature. wrapping your handset cable over the bracket and letting the handset dangle works just fine. I decided to put a bracket on my dash however to hold the mic in place.For a mounting a radio in a JK, this is one of the best options hands down. I would buy this again in a heartbeat.

This mount is great. I originally mounted my CB above the rear view mirror but I attached it to the plastic trim piece. I never liked it and was always looking for a better mounting solution. I found this by dumb luck on a forum and ordered it. It uses the same attachment points as the footman loop. Works great. I was concerned it would not be strong enough to hold my 29LTD Classic full size CB, but it holds it fine.I have a 2012, and the footman loop attaches via T-15 torx screws. Simple installation. If you have a 2007-2011 the instructions state you have to drill out the rivets for the footman loop and then insert some type of attachment pieces.All in all this is a great solution for mounting a CB in a JK Wrangler.

Direct fit and super easy install

A good and original cb mounts for Jeep. Does not block the rearview mirror, does not obstruct vision

Nice mount. I like that it puts my GMRS radio up and out of the way and still be useable. My radio is 7.5x 5.7 x 1.85 inches, and I had to drill an extra hole to move my radio forward to keep it from touching the rear view mirror. And a wider radio would require me to offset the radio farther to the right to get clearance for my drivers side visor. It bounces a bit more than I would like or had hoped with the weight of my GMRS Mobile which is @2.5 pounds.