DROK DC Motor Driver, L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation

This unit is perfect for my application with a couple of 2-3 amp DC motors and worth far more than the cost. I require frequent direction changes and large starting current spikes, but the board stays cool and doesn't need heat sinks. The connectors have screw terminals and removable snap lock connectors which are excellent.The documentation looks great on glossy paper but needs some clarification.Here's a few tips and a Arduino test setup:1) This double H-bridge can run two motors independently of each other.2) Each motor can run forward, reverse, brake, full speed forward, and full speed reverse.3) Categories of inputs (you provide these) to the board are:a) Main power (up to 15 amps) that is used to drive both motors. Read the instructions around voltages, current, peak current, fuses, etc...b) Control logic for Motor Ac) Control logic for Motor Bd) 5v power you provide into the board for it's logic processing, etc.. with very little current draw.4) For the main power input, you need a capable power supply. I'm using a 10amp battery charger.5) You must feed 5v into the board. The board has 5v (and ground) pins for each motor, but you only need to provide 5v and ground on one set of pins.6) Each motor needs three 5v logic inputs. For motor #1 they are labeled IN1, IN2, and ENA1.7) The two pins labeled IN1 and IN2 are fed from any two GPIO(Arduino) pins with HIGH or LOW to control the mode of the motor such as forward, reverse and brake. See the control logic table in the instructions.8) The pin labeled ENA1 REQUIRES!!! a PWM output from Arudino. You MUST NOT apply a steady voltage from something like a potentiometer or DAC output.9) Here's a basic test setup for Arduino UNO if you need it:Connect 5v and ground to H-bridge,Connect main powerConnect motor(s), you just need motor A for this testConnect Ardunio pin2 -> H-bridge pin IN1Connect Ardunio pin3 -> H-bridge pin ENAConnect Ardunio pin4 -> H-bridge pin IN2Create a test sketch as follows:void setup() {pinMode(2, OUTPUT);pinMode(3, OUTPUT);pinMode(4, OUTPUT);}void loop() {digitalWrite(2, LOW); //forwarddigitalWrite(4, HIGH); //forwardanalogWrite(3, 178); //pin 3 is PWM, 178/255 = (about) 70% speed. Max is 255.delay(1500);digitalWrite(2, HIGH); //reversedigitalWrite(4, LOW); //reverseanalogWrite(3, 76); //pin 3 is PWM, 76/255 = (about) 30% speed. Max is 255.delay(3000);}Hope this helps get you started.

Works great with my Arduino Uno. Powering a 12v wiper motor.

So the motherboard for my Apollo 835 Dual Swing Gate finally kicked the bucket after 20 years.While a replacement motherboard for my gate model was available for purchase, they were charging 500 bucks for it (and I was pretty sure I could do it for 50 bucks or less)The actuators that came with the dual swing gate kit operated at 12 volts with a fuse on the board limiting them to 3 amps. This made this dual L298 motor driver perfect in my quest to replace the motherboard.This dual L298 configuration has a similar pinout to just a single L298 board, except there are two of them. It still requires 12 volts to run the motor and a separate 5 volt to power the L298. The 5-volt pins for the L298 are connected so you only need a single pair of power cables.After writing some code for an Arduino Nano to mimic the original motherboard operation and rewiring each Swing gate actuator to work with the Nano and this motor driver. I was able to successfully replace the motherboard with about 20 dollars worth of new parts.A 3 Amp fuse is placed in series between the motor and the motor driver to prevent the motors from being damaged or if an object interferes when the gate is opening or closing. The motors don't have too much torque behind them, and the gates aren't heavy to move.While its current installation isn't pretty lol, it does not rain a lot where I am, and it also sits inside a weather-resistant metal box.I haven't had any issues for the past 3 mo since I installed this. (other than updating the programming on the Nano to fix some kinks)11/10 saved 470 bucks.

The controller is driving 1 pair of 12V DC motors on my unit (tank treads base unit).Current draw 2~3 amps going forward\backwards, with spikes of up to ~5A when turning (each motor).Pros:- Controller only gets slightly warm, so very happy about this as the previous one I was using was getting very hot.- This board included the wire connector, a big plus!Cons:The controller needs a total of 6 I/O's for controlling 2 motors with PWM. 4 I/O's for setting FWD\REV and 2 more for PWM (for each motor).No onboard 5V supply, you need yet another wire to get +5V into the controller (although low current requirement since it's only for the logic).The Manual included has a hard time explaining what the "+5v" pins are for: connect +5V here for the logic otherwise the board won't work.I hope this helps.

To Glen, I don't do much with electronics but in the process of building a project it came to my attention a microcontroller was needed. My skills are in fabrication of wood and metal. If it's made of wood or made of metal I can build it. When it comes to arduino and writing code with understanding its been challenging. The code you provided gives me something to work with where it's so hard getting a straight answer out of people. Between work, home responsibilities, kids and grand kids I don't have tge luxury of time to learn all the details of writing code. I learn what I can when I can. Thanks for unselfishly posting that

the board and the instructions included were amazing. fast and easy setup also it was the best item for my uses an a HIGH amp driver board i could find nothing else like this for this price and quality. i would defiantly buy it again and will buy more for future projects.

I ordered three drivers. One of the drivers arrived broken and unable to use (it was missing the piece that connects to ground and power)! Planning to return to get my money back.

just like the l298n, but it can handle a read load. keep in mind you must supply 3.3v for the logic ,5 volts will light the LED, but confuse the logic. Excellent board and low heat!