WRT3200ACM: AC3200 Dual-Band Gigabit Wi-Fi Router, Beamforming Tri-Stream Wireless Signal, Ethernet Ports, MU-MIMO (Black, Blue)

WRT 3200ACM A very nice product, setup was very simple. Overall performance verses my 4 year old WD N900 router is much better; improved signal strength, improved throughput and so far no drop outs. I started getting drop outs on the old router when we exceeded 12 devices, the WRT has run flawlessly with up to 21 devices so far. The unit runs quiet and cool – no fan needed, which is nice since fan noise can be quiet annoying. I manually configured the router (enter 192.168.1.1 into your browser) and used “Smart Setup Tool” to get connected to the internet and do a basic configuration, the setup tool makes this very easy. After that I manually edited a few parameters to “personalize” the network, simplify management and optimize performance as follows: Changed name of the 5GHz network rather than accept the default of “Name of 2.4Ghz” appended with _5Ghz. Edited the guest network names and password and turned it off, I will switch it on if needed. Renamed some of the devices on the network map so that it is obvious which device is which. This make the network map much more useful. Edited the Host Name and Network Name, personal preference. Turned off the ability to manage this router wirelessly via Linksys Smart Wi-Fi (Connectivity – Administration tab) to reduce the chance of a wireless hack. Wireless networking defaults were not optimal for our network so I made the following changes: Set the 2.4 GHz network to 802.11gn. This router does not support 801.11b so I don’t think there is a difference between the mixed setting and the 802.11gn setting. I don’t have any legacy b only devices so this is not a problem. Not supporting 802.11b avoids the 2.4 GHz radio having to do gymnastics to talk to any b devices this helps 2.4 GHz throughput and avoids the slight decrease in n or g throughput that results from a mixed (with b) setting. I thought about using n only but since g and n can play together (the overhead associated with sending a legacy preamble before the HT preamble is small and g devices can interpret the n preamble) I left g available. I left the channel width setting on auto and it selected 40 MHz i.e., twice the width and double the data rate of the legacy channels. Set the 5 GHz network to ac only to allow optimum 5 GHz performance, I left the channel width setting on auto and it selected 80 MHz i.e., four times the width and four times the data rate of the legacy channels. I am not quite sure what they mean in the advertising info with regard to 160 MHz channel width since this device only has 4 antennas and 6 are needed to get 160 MHz bandwidth. I left the channel selection on auto for both networks. Restricting the router protocols has some potential disadvantages: 1. Legacy devices that are restricted to 2.4 GHz b and/or 5 GHz a and n only will not be able to connect, so if you have older devices this might be a problem. 2. If there are devices running 2.4 GHz b and 5 GHz a and n nearby they might interfere with your network and your network router might interfere with them. I am too far away from my neighbors for this to be a problem but if your neighbors are close you should probably use mixed mode. Given that the 802.11g protocol was released in 2003 and that manufactures built 802.11g chipsets before 2003 I doubt that many people have many 802.11b devices only. I would like to know if there is a difference between the between the 2.4 GHz mixed setting and the 2.4 GHz 802.11gn setting. Does the router listen for 802.11b signals and back off to allow legacy transmission to a legacy router when 2.4 GHz mixed is selected? I called tech support but the person I spoke too did not seem to know what I was talking about. Some users have reported signal strength gains, I measured the signal strength (using a Wi-Fi Analyzer on my phone) before and after installing the new router (in the same location). On the 2.4Ghz band the signal strength increased by an average of 3dB (double the power) running g and n protocols. This is not a huge improvement but will help in areas with marginal signal strength that are prone to signal drop outs. The increase in signal strength on 2.4Ghz varied from -1dB to 8dB, in looking at the results it looks like beam forming is working and increasing the signal strength in the areas with 2.4Ghz devices with up to an 8dB increase and an average of 4.5dB. On the 5 GHz band the signal strength increased by an average of 16dB (40 times the power) running mixed mode. This made some previously unreachable (for 5G Hz) areas of the house usable for Wi-Fi and is a great gain in signal strength. The 5 GHz radio designs have probably got a lot better in the last few years and this result alone is a good reason to buy this router. The increase in signal strength varied from 11dB to 20dB and did not seem to be affected by beam forming (possibly due to the fact that phone that I used to take the measurements was on the 5 GHz Wi-Fi network when I took the measurements). It is a good idea to back up your router configuration (Troubleshooting – Diagnostics tab) to allow a quick restore in the event you have to reset your router. The Troubleshooting Status report pages are very nice to have. It would be nice if you could search the router help information embedded on the router. The user guide does not cover as much as the help information on the router and he use of screen shots in the manual limit your ability to search (e.g., you cannot find Backup or Restore by searching the user manual). I am very happy with this product.

I bought this back in 2017 with the intent of upgrading a then-10-year-old Linksys WRT54G router that had served with honor and distinction through many LAN parties, firmware flashes, and general abuse. As expected, the WRT3200ACM has been the rock-solid basis of my home network ever since its first power-on event. I have only upgraded the firmware once, and that was with the stock firmware from Linksys. No OpenWRT or third-party firmware, although I vehemently support using third-party firmware. My 54G had dd-wrt on it and I loved it! When I bought the 3200 new, it was not even on the list of supported routers! Now that it is? Meh... Ain't broke, don't mess with it. The range is great! I can be in my garage about 100 feet away (no obstructions but 1 thin wall) with nearly full signal. It makes playing my wifi radio in the garage so nice! The part that makes me so happy is the amount of wired and wireless objects I can have running on the same home network. My place is chock-full of wifi stuff: wireless lighting (maybe 20 bulbs now?), a couple of Samsung TVs, two wifi radios, several phones, some Alexa units, my girlfriend's tablet, a pair of home theater PCs, and a CPAP machine, all getting along with no conflicts. That's not even counting the wired PC and printers and other various bits of equipment being wired in through a managed HP 16-port network switch. I know it says 32 wireless things is the limit, but everything is still working just fine. For now. :)

I've waited a little over a month to review this product. As you can see it has so far "met my expectations". I've been using a Linksys WRT54GS Wireless-G Broadband Router for over 11 years and hope the Linksys WRT AC3200 Open Source Dual-Band Gigabit Smart Wireless Router serves me as well. I made the change because we've accumulated a bunch of devices connecting to the Internet through the router and felt a more up-to-date router might move data better. Also upgrading meant adding a frequency (5meg) so I was looking to improve speed that way. The installation went pretty well. After the initial part of the setup I was able to change the network SSID and password to my original router information so that saved me re-connecting each 2.4meg device (which for us was about a dozen devices-3 Roku's, 2 Kindles, 1 smart phone, 1 iPad, 1 iPod, 2 wireless printers, 1 network laser). All but the network laser printer took off immediately. My old network cable needed to be replaced by the cable that came with the new router to fix that problem. The 5meg frequency seems to reach anywhere in our home where we use laptops so they were connected to that network. Our DSL Internet service is adequate but not super fast (10 meg) but the system seems adequate even when the visiting kids make their VPN connections to work. The router runs quite cool considering it doesn't have a fan. Windows 10 seems to have Network Discovery hang-ups yet but that can be corrected by plugging in a USB memory stick. I tried it first with a spare memory stick which has subsequently been replaced with a faster, bigger capacity version formatted for NTFS which allows for some of my bigger files (video and data). The plus for plugging the memory stick in the back of the router is that it serves as a media server and you can play your music, video's and photos on a smart TV. I won't know whether my new Linksys router will last for a while but so far I like it a lot.

I bought 2 of these, one for myself and one for a family member. We're experiencing solid WiFi where before we both had flaky WiFi. There's lots of good configuration options and features. For the price I think they could have gone a little further with those but it's not holding us back from normal use.

With so many options listed on Amazon, I was confused which to buy. But decided to go for this one and it turned out to be exactly the right one I was looking for ! Brand new, Middle East version. Price was significantly lower than in Carrefour or Sharad DG! Coming to router - I bought this as it was recommended by ExpressVPN. It was easy to download and flash the router. Although it limits a lot of the default features - you get 2.4 & 5 GHz bands at desired country server. Split tune long enables certain devices to have no VPN and rest to have selected VPN. The range is weak though - network doesn’t go beyond 2 thick walls.

The product arrived within the specified delivery date and in good condition. Set up was easy and it worked perfectly. Highly recommended l.

Do not buy this. It comes with a closed source operating system. Disgusting behaviour

Bought from Amazon AUSTRALIA, and delivered today. However, it did NOT come with an Australian plug. Now I have to also buy a US-to-AU adapter, one that is rotated by 90° if I want to fit it into my power board, or a suitable replacement adapter with an Australian plug. Really? That just sucks. There was NO warning in the product description that it would come with a US plug only. If I buy something from Amazon Australia I think I can expect to be able to use it in Australia out of the bloody box!!!