394mil 10mm 16.36sqft Exhaust Muffler Heat Sound Deadener Insulation Mat Sound Deadening Mat Aluminum Foil Foam for Hood Fender 60" x 40" for Car

Works great! Great value! I used this to insulate around my window air conditioners that overlook a NYC street. I wanted sound and temperature blocking and this works great. The adhesive is strong, so you can't relocate it after it's been pressed into place. Removing it leaves a this layer of foam which takes some elbow grease to remove. It was easy to cut and install then it stays in-place. It does a great job blocking noise.

If you build a camper of sorts, van, bus or trailer this is what is best to start with! Great sound proving a some insulation too.

This product is pretty nice for the cost. The adhesive is surprising good. When you first time you feel it, it doesn't seem like it's very strong, but it sticks very well. The paper comes off fairly well, but tears easily, so you might need to pick it apart a little bit. This material is really designed for temperature insulation and not noise insulation. I wanted to try it out after seeing so many reviews about using it for sound insulation, so I bought 5 rolls to apply to my Geo Metro. I laid down some vibration dampener first and then did complete coverage on the floor from the firewall to the trunk. I had about 70% of one roll left, so a normal sized was will probably require 6 or more rolls. I had doubts about using this for sound control because it is just a foam material; there is no weight to this product, so blocking any low frequency sound was out of the question (road noise, exhaust or tire noise). If you paired this product with something like MLV, you might get good results, but this material is a 1/4 inch thick, so you wouldn't have room to apply it with another barrier. The result? There was a reduction in wind noise, but the exhaust and general road noise were unaffected. I still think this is a quality product, but you need to make sure you're using it for the right application. I knocked a star because it was marketed as a sound deadening material. If you want good sound control, I would suggest using 25% coverage with a vibration dampening material (Dynamat, fatmat) and then 100% coverage with a two-in-one closed cell foam and MLV product like Second Skin Luxury Liner Pro.

I was referred to this product through the vanlife Facebook group. This is my third purchase of this product for use in my camper van. It is cheaper than the square sound dampening panels that you roll to adhere. And these have the added benefit of being insulative. I converted a minivan and used this on all the outer wall surfaces and in my trunk space before adding another layer of Havelock wool insulation. I noticed an effect right away after I had gutted the interior of my van down to the bare metal. Hardly any road noise and no 'jingling' could be heard while driving even prior to building out the interior. Definitely recommend for all my fellow van-lifers! One tip... make sure you wear gloves when applying this. The adhesive is super strong it's a pain to remove it from your bare skin!

This material worked out perfectly for my 98' Toyota Camry and looks great! Simply roll out the new insulation material then place your old hood insulator over it (pick any corner) and trace around the old hood insulator and make marks to cut for engine labels and little dots for aligning the plastic hood retainers. My 98' Camry takes 11 hood retainer clips. I dropped one into the engine bay and lost it LOL so ten will do. The adhesion sticks instantly to the hood, so keep this in mind. When you're done with the cut-outs and are ready to apply it to your hood, I recommend using a spray bottle with rubbing alcohol and spray down your hood and use some paper towels to clean it. Peel half of the paper from the adhesive side back and apply it slowly while aligning and placing in your hood clips aswell. I recommend doing this during warm weather, so the adhesive makes the right stick. I am pleased with this product the hood on my vehicle is cold to the touch; at most it's a tad bit warm if anything! The material does provide sound deadening as well, which I've noticed when the car is idling. I would highly recommend this product over your cars OEM hood insulator. I went to find out the price of my cars OEM hood insulator, and they wanted $260 for it. Psst! Forget that! This insulation material worked just as great for a replacement!

Purchased twice. Used as boat engine compartment insulation and rear cabin wall insulation in my 2019 Ram truck. Worked well in both applications.

Not exactly 60x40, it’s 2” short. Not the end of the world but clearly not the size advertised. Otherwise.m, quality is good and the sticky back is really sticky and stayed on. Overall pleased with this just wish the measurements advertised were accurate.

Squrrels destroyed original underhood insulation mat on my friend's car and she asked me to help to replace it. I checked prices for OEM part, it was too high. I looked for another solution and found this mat. It cost $36, not few hundreds. With the adhesive backing it was very easy to install. It has good temperature and noise insulation. Now after 3 years it still looks like new and squirells don't touch it. My friend is really happy with it.

Price and quality is super -easy to cut and stick very well on clean surfaces. -the noise from my diesel engine is reduced really noticeable.

très bon

Heat Shield 197Mil 6.46Mq: l'ultima parte 6.46Mq è ingannevole, non è una unità di misura e ci sia aspetta che ci siano tanti fogli fino ai 6.46Mq che immaginavo fossero metri quadri e non misure immaginarie. Non c'è alcuna rispondenza con le misure del tatpetino (areali?). La dimensione vera è quella del singolo foglio, espressa correttamente in pollici, 40" x 24", riportata alla fine della descrizione. Attenzione il foglio è uno solo, pertanto non se ne giustifica il prezzo, alto rispetto ad altre proposte presenti sul Amazon.

As advertised, The glue on backing really grabs hold and stays in place. I recommend this product !

Die Klebeleistung der Matte ist nicht ausreichend und verhindert eine sachgerechte Verwendung.