High Glossy Wood Grain Vinyl Wrap Sticker Decal Car Internal Wraps Self Adhesive DIY Film, Waterproof Wrap Roll Without Bubble, 100x 40cm/39.4x15.7in (Yellowish-Brown)

It was great stuff looked o.em.cut very well adhesion is strong

I had never wrapped anything except a present - and not very well. I had no prior training or knowledge of vinyl wrapping. This was used to cover plastic panels on the dashboard of my car. This material was thick and strong. Backing was very sticky. Looked really great. Used a low heat gun (120 C) on edges, curves, rounded corners and contours to get a smooth, wrinkle free surface. Even screw holes came out great using an ink pen point and pencil erasure to shape. I was amazed at how easy it was to work once I learned how to cut for holes and other openings. Don't over cut or cut flush at first. Heat, stretch and fold to inside. Quality material. Withstands heat without bubbling. Biggest issue was to have and keep a clean, smooth substrate. Any dirt or chips will show in your final work. CLEAN, CLEAN is the key. Did have a few bubbles develop. Poked with a needle, heated and smoothed OK. Used single edge razor blade, old credit card with gauze pad on edge and fingers. No special tools. IMHO, surface was too glossy - sprayed with clear satin. Much better. Very impressed.

Very good quality but I gave it a 3 star because of the shoddy way it was packaged. As you can see in the picture 4” of the roll is unusable with all of the different tape they put on it. Sorry but when you are paying $15.00 a little roll that’s a lot to have wasted.

Impressed with how forgiving this stuff is. If you accidentally crease or wrinkle it or have to lift it again, you can heat it up to undo a lot of damage. Don’t overheat it though, it becomes shiny if you do. It’s very sticky and holds onto smooth surfaces well. I was a bit disappointed with its malleability. It’s much thicker than I thought it would be, which can be a positive for flat surfaces, but for surfaces that dip, concave or have different slopes that meet, it can be hard to get it to sit flush which was the main problem I ran into around my cupholders. You can push firmly with a sewing needle to discreetly poke a hole and release air bubbles. Turned out mostly good, just couldn’t get it to sit perfectly around my cupholders.

I bought this to match a missing trim piece in a 2010 Mercedes E350. Known problem where the door trim strip falls off. I bought the car and the trim was missing. Purchased this roll of contact trim and it matched perfectly. It was easy to work with, not flimsy. Stuck properly and I was able to trim it with an exacto knife. Time will tell if the summer heat will affect it, but I did clean the surface with rubbing alcohol first, so I had a proper surface for this trim. I have plenty left over in case it fails, but for now it looks like a factory piece. BTW, Mercedes wants over $300 for this trim and it's very involved with taking of the door panel and fitting the new piece. All that was avoided using this product. Had it done in 20 minutes.

Didn't like the way it went on or the way it looked didn't end up using it 😕

Look great and fairly easy to apply. I did the dash panel on my Cadillac. Because of the shape and buttons, it took more time but look perfect

I’ve worked with a lot of vinyls but this is the worst. Its too ridged so if you try to install it on anything that is not flat you will have wrinkles. Applying heat only makes it worse, even on the lowest setting on my heat gun the vinyl either distorts, bubbles up or looses adhesion

J'aime ,semble original de l'auto

المنتج غير وليس هو الذي طلبته وبسبب ذلك هذا آخر طلباتي من أمزون

Hard to work with, but after 2nd attempt I'm happy with results. Not 3m but Seems to be pretty sticky