Rapid Tac Application Fluid 4oz Spray Bottle | Bubble-Free Application | Allows Graphic to Be Re-Positioned Before Bonding | Bonds in 90 Seconds | for Vinyl Wraps, Decals & Stickers

Good stuff. Made a big difference in applying vinyl! Thank you.

We have motorcycles -- not like most normal people have cars and bikes, I'm talking 25 in the garage right now, and we've owned and restored hundreds over the years (I know, we're weird). Dirt bikes, adventure bikes, vintage motocrossers and modern sport bikes all require the application of decals at some point or another, so you can imagine how many times I've applied the darned things.I've tried all the tricks - alcohol, half alcohol and water, Windex, etc. etc. Some of these things do allow easier placement but degrade the ability of the decal edge to adhere effectively over time. Others allow adhesion too quickly. Nearly everything leaves at least a few bubbles which are impossible to squeegee to the edges so I end up poking them with a pin to remove them, leaving small spots where dirt and grime collect and are difficult to remove.So, when the hubby bought an expensive set of decals for his new sportbike, you can imagine how thrilled I was to have the job of applying them. Not only was this a project that had to look good, it had to stay looking good for a long time. Add to the complexities of this installation is the fact that every one of these 12 decal locations had compound radii which required the flat decals to conform to curved plastic. Fuuuun.I knew my regular process of spraying everything with water/alcohol/soap mixture, cussing, squeegeeing, cussing, using the heat gun, then cussing some more wasn't gong to cut it, so I did some internet searching. Many online forums later I decided to try Rapid Tac.I purchased the Rapid Tac Application Fluid and Rapid Prep Cleaner, yes they're not cheap, and yes they come in a small bottle, but if they could help me produce good results without ruining an expensive decal kit I considered it a good investment.I brought all the plastic inside the house, removed the old graphics then washed everything in hot soapy water, I then set it aside to dry completely overnight. The next morning I double checked the installation information given on the Rapid Tac website, then carefully wiped down the first piece of plastic with the Rapid Prep using regular cheap paper towels as recommended. I then sprayed Rapid Tac on the plastic, removed the backing on the decal and sprayed it down, then applied the decal. Once it was placed properly (after a couple of easy repositions) I started squeegeeing out the fluid starting in the middle. The fluid came out easily and without bubbles. I used a heat gun to ease the decal around corners and was able to work the decal for at least 15 minutes before things dried completely and began to set up.All 12 decals were installed on 6 pieces of plastic in about an hour. There's no bubbles, no wrinkles, and the job looks like it was done professionally. I would have never been able to do this without Rapid Tac.If this is your first time installing graphics you won't be able to grasp just how incredibly helpful this product is, but if you've struggled with getting perfect results before you're going to absolutely love this stuff. Follow the directions, be sure you're working with a 100% clean surface, you'll be amazed with the results.

I used this fluid to apply vinyl pinstriping tape to my bicycle. Normally I would not bother with such things, but my new bicycle had its manufacturer name written 12 times and model name three times on its frame. I have found this excessive -- I respect designers of this bicycle very much, but it was as if I was riding a sample stock photo covered in watermarks. So I had to reduce it to somewhat reasonable manufacturer name 8 times and no model name. The problem was, one of the areas required precise positioning, so tape combined with existing pattern would convert a giant label into two pinstripes. That required precise positioning 450x25mm piece of tape to form a 3mm gap on both sides between the tape and the edge of a painted areas. What could not be done while applying tape to a curved surface without any ability to re-position it. With this liquid, I was able to position the tape precisely, and so far it looks like there was no detrimental effect on the adhesive bond, compared to all other areas where smaller pieces were applied without a liquid.

Works Great for wet application for decals especially larger decals .. squeegee the air bubbles out and after that ya can peel and still work out bubbles if needed to .. like tinting windows almost .. used it for hood decall on my Jeep Mojave .. and side decals too .. and a little goes a long ways too .. mist and set and squeegee away .

Personally I don't like this at ALL. I bought it for sublimating on glass using laminating film. Nothing at ALL I liked about it...smell...adhesion...value for money, ease of use and the list goes on. I found it very difficult to get and MAINTAIN a seal on the glass without incurring bubbles or streaks. I then read about a gentleman that uses water, a drop or two of dish soap and alcohol so I gave it a try and VOILA! I'm sold on making my own. In my opinion, MUCH easier to use and the cost is next to nothing.

Item arrived on time, performs as advertised I recommend this to others who have vinyl decals to apply to rockets or any other project

This is the real stuffWorks awesome

Between the hood and the bumper of a RAV 4 is about a 50" x 5" strip of metal that gets hit and the paint chipped by rocks thrown up from the roadways. A Hood protector helps take care of the hood itself and deflects for the windshield but still leaves the 50" x 5" painted area prone to rock chips. I installed XPel only paint protection film to cover the area and this spray made the alignment of the vinyl really easy to align and once in place the vinyl was easy to squeegee out the bubbles and when dried helps the vinyl adhere quite well. Have always mixed up some Dawn and water in a spray bottle for such installs, but this is so easy to use, gives plenty of time to work with the vinyl, and really helps it adhere to corners and folds. Would buy again, but a small bottle goes a long way. Did two cars and still have 1/2 bottle left!