4036ER2004A 4280FR4048L Front Load Washer Tub Bearings and Seal Kit | Fit for LG & Kenmore Etc,Replacement Part 4036ER2004A 4280FR4048L 4280FR4048E(MAP61913707) 4036ER4001B- 5 YEARS WARRANTY

Machine ran as good as new after replacing these parts, and is still running 10 months later. It was a difficult 8-hour DIY repair, but worth it, considering the poor lifespan of new machines.

I’ve had these bearings installed for just short of a month and they have performed exceptionally! My LG washer is a bit over 10 years old and the original bearings and seal had never been replaced. The inner drum had quite a bit of free play and sounded like a fighter jet anytime the machine would do a spin cycle. Upon taking everything apart, I did find that the bearings were terribly damaged because the original seal had failed and let water into them. The spider assembly also had some marring, so I knew that I would need to do this job again with a new spider at some point. Given this information, I opened these new bearings and packed them with automotive heavy duty grease. From the factory these bearings don’t have much grease in them, so I would recommend doing this regardless. Additionally, I put the new bearings in my freezer while I finished preparing the drum for installation. Putting them in the freezer helped them fit right in with minimal mechanical persuasion. Overall, I am happy with the purchase and will update should the bearings fail. So far after a month, everything has been great!

First set lasted 103 days (3 months and 12 days). Replacement lasted 209 days (6 months and 28 days). Purchased a 2nd second that last 197 days (6 months and 14 days). Description stated 5 year warranty and the company does not respond. These bearings are worthless. Don't waste your time with these bearings.

My washer sounded like a jet was taking off when it was running the spin cycle. We've had this washer/dryer set for 15 years. After researching quite a few YouTube videos I determined it was the bearings. The reviews on this set aren't great but I decided it was cheap enough to risk it. The inner bearing and seal fit perfectly. The outer bearing seemed like it was a little small. I'm a millwright by trade so I have the tools and the ability to mic the ID and OD but it was a close enough fit that I wasn't worried it world come apart. I did have to peen the sides of the outer aluminum piece on the drum to keep it in place. I also opened the window on one of the bearings and I can tell you that there isn't much grease inside. I decided to not add any in case that was intentional. I didn't want to compromise it by adding grease and having it fall prematurely. It's been running clothes for 4 humans for approximately a month now and we haven't had any issues. The rubber "O" ring fit just fine. I went around 2-3 times making sure it wasn't pinched or standing up. 5 stars so far!

Great kit..just wasn’t a fit. Returned this item.

My LG washing machine sounded like a freight train. Ordered this kit and took my time to install it correctly. My washer works and sounds like new now! Few tips, when you get the bearings, put them in the freezer. They will shrink slightly and be easier to install. When installing the bearings put a little oil on the outside of them to help with driving them in. Keep your olod bearings, clean them off good and use them to drive the new bearings in. Also put a little axle grease on the shaft and on top of the inner bearing to help keep it from seizing up and rusting. It also helps with installation of the drum. Put a little grease on the splines as well. And don't forget to put some fresh blue locktite on the stater bolt on the back of the motor. Also put a little vasiline on the drum gasket before you install it, it will keep it from fry rotting. Chang the drum bearings before it quits working. If it starts making noise it time to replace them. The longer you wait the more seized they get. If you are a diy type person then this won't be to bad. But you do have to dismantle the whole machine. There are some good videos on YouTube.

Bought the parts for a older washer. Worked great about 9 months then got noisy, still work 1 year later and still noisy 1 year later.

Seller stands behind product. I got a warranty 1-1/2 years after use / purchase. I would have opted for higher quality bearings if available because the removal job is difficult compared to the cost of the bearings. I have an ~10 year old LG Direct Drive washer which has had the ‘all plastic rotor hub’ (4413ER) replaced many times. I assume that’s due to an engineering mishap on LG’s behalf since they upgraded the dampening ‘all plastic hub’ with a metal insert one that hasn’t failed yet. Only problem with that is it puts pulsation from the Direct Drive VFD’s magnetic forces directly on the bearings. I think this causes seal fatigue and the bearings to fail prematurely. I have to give TOMOON / wsh supplier credit as they did stand behind their "5 YEARS WARRANTY". They shipped a whole rebuild kit under warranty very quickly. Thank you TOMOON you earned my 100% 5 star review.

Excelente producto balero para lavadora lg

I recently rebuilt my ~2009 LG washing machine. It began to make some horrible noise while spinning. Unfortunately I could not find a repairmen who would help. Everyone I spoke to said they wont touch either LG or Samsung washers or dryers due to thier poor quality. Knowing that the bearings needed replacement, I ordered these parts and began to dissassemble the washing machine. Additionally, I ended up having to purchase a new spider to replace a corroded spider on the back of the drum as well as new shocks and a multi valve. Basically this was a full rebuild. the whole repair efectively took around 10hrs of work but was able to assemble it. Once I got everything together, it ran smoothly like new. When I asked a appliance parts store whether the bearing were good quality, their reponse was that they are probable better than the ones that LG originally used. All in, I spent around $600 CAD and probably avoided paying between $1600-$1800 CAD for a new unit. I understand the repair peoples lack of interest of working on the machine. If you include parts and labour, it better to buy a new unit but if you do it yourself, it makes sense. The washinig machine is running great since the repair around 5 months ago. So far I recommend this bearing/seal kit.

Bearings look well made and fitted exactly. Seal kit string was too long, had to reuse the old one. I succeeded in repairing my washer. Too bad the fix lasted only 8 months. The metal bushing on my washer drum spider was too much damaged to garantee a lasting repair.

Checked the questions to see if this fit my specific model of washing machine, and it didn't even though the seller answered yes that it fits to someone with the same machine as me lg wm3500cw. 1 bearing was the correct size and 1 bearing/ seal were incorrect sizes. Really disappointing after waiting 2-3 weeks after ordering.

Bearings and rear seal fit great. The large o-ring / gasket for the tub seam was too large for our washer, despite being the correct part number according to searspartsdirect.com. We re-used the old gasket which was not leaking before replacing the bearings, but leaked after replacing them. So we'll have to do our best with the old seal and some silicone to reinforce it. Washer model: Kenmore 796.40277900