Broan-NuTone SP3004 Reversible Stainless Steel Backsplash Range Hood Wall Shield for Kitchen, 24 by 30-Inch

After getting new appliances, the oven we chose didn’t have any kind of backsplash. Since we’ll eventually put in tile, we decided on this for an oven backsplash. It was actually thicker than I thought it would be after reading some reviews. I’d have to agree with other reviewers that screws should have been provided. I didn’t have any issues wit bent corners or scratches. It came packaged like a painting. I did go out and buy some drywall anchors and screws (#10 or 3/16”). After peeling only the corners of the protective film, I put it where I wanted and with the help of another person, marked the screw holes. I will have to say that doing this BEFORE the installation of the stove would have made this a whole lot easier. As it was I had to pull the oven out because the backsplash extended below the back of the oven. I did run into the issue of putting it as high as I could that made drilling and then screwing in the screws a little difficult (drill clearance). Initially I left the screws a little loose so I could have a little maneuvering room while installing the screws (a two person job, unless you’re putting on some kind of adhesive). Unless you are below eye level of the microwave you don’t even see the screws. After I tightened all the screws I removed the protective film. If you’re using only adhesive, I’d make sure you’re hold it as pulling off the film made the backsplash bow. If I didn’t use wall anchors I can see it pulling out of the wall. Overall it didn’t take that long to install. I like the finished look as it matches the other appliances.

Just purchased a stove that doesn’t have the part in the back that is above the burners. My current tile backsplash showed so I needed something to cover the gap. I didn’t even know these existed until now. WOW! This is perfect since it’s designed for behind a stove. Very sturdy and installed in a minute. I bought stainless steel screws for installation. Looks fantastic with my stainless steel stove. Matches beautifully and clean up is a breeze! Highly recommend this item.

I must say that this product is excellet. Why? It was sent in a box that is strong and dent-proof. The measurements are precise. Predrilled 4 holes so it was ready for installation. I must also thank to delivery, on time and with care (this time Amazon delivery was made by our local Usps). Yes, it is stainless steel and can hold magnets. Just what i was looking for. A little bit pricey though…

This is a very durable piece of stainless steel. Cut straight, easy to clean, and installing was a breeze. Now for the negatives. It came in a box, inside another box; but with no foam or other protective packaging materials, so the smaller box which held it was just sliding around in the larger box. There are 2 scratches, one on the top and one on the bottom; so I couldn’t hang it to hide them. Fortunately, once I cleaned it, they almost disappeared and kind of go with the grain so they’re unnoticeable unless you know they’re there. Lastly, there was no protective film on the front. Installation took a little longer bc of this, which wasn’t a problem; but had to be extra careful not to scratch it up while installing. Overall I give 4 stars, bc it makes my newly remodeled kitchen look even better than it already did.

It is a sheet of stainless not much to say about it

I'm very happy with this. I wanted a simple stainless backsplash. My wife wanted something with a pattern. Since I'm the cook and cleaner, I don't want textured surface to clean. Plus what we saw were all stick-ons. I'm thinking sooner or later stick-ons fall off from the harsh environment over the stove. And the ones that don't fall off ruin the drywall when you need to remove them. I installed this with screws only. It lays reasonably flat against the wall. I might put a micro bead of caulk around the edges to prevent any water getting behind from a large splash or while cleaning. I didn't want to glue or caulk behind it in case I want to remove it without destroying it. Installation tips at the end of the review. I was worried about shipping but this came well packed. Even though I bought this as Amazon Prime, I believe Amazon drop shipped this one from NuTone. It came in a heavy flat cardboard box but the box was thoroughly fiberglass strapped to a sheet of Masonite board larger than the box on all sides. The Masonite had chipped edges and corners but the product box was unscathed as was the actual sheet. The good side had protective film and the non-filmed side looked pretty good but brushed a little more coarsely. Not sure why they call this 'reversible'. The 'good side' was finished identically as my NuTone hood. Mine is magnetic. Neodymium magnets stick very strongly. Regular magnets stick ok too. Tips... Check the wall first and scrape off any imperfections that might prevent the sheet from laying flat. Leave protective film on. Take your time and drill your holes carefully. I held in place and marked all holes. Then I drilled one top hole and installed the drywall anchor. I held the sheet up again and installed the one screw and rechecked the other top hole location. Remove, drill, repeat. I rechecked the fit and my marks before drilling each hole. Drill bits tend to wander in drywall so I used a tiny pilot bit first. You want these holes PERFECT. If the screws bind with the holes on the backsplash, the sheet will not lay flat when you get all 4 in. #8 screws are recommended but I used #6 stainless screws and washers to give me a little more leeway. When you are finally ready to screw it down, peel back the film only at each corner. Screw it down and don't crank the screws hard at all. Just very gently snug. Now peel the film off. Be careful, it's stuck pretty good so peel at a low angle to not accidentally pull/bend the sheet away from the wall. Press down on the sheet as you peel just in case. If you have some gaps to the wall, squeeze a drop of calk under it and tape down till dry. I don't recommend applying glue or caulk to the back prior to installing. You will surely bend the material and ruin the drywall if you ever need to remove this for some reason.

Not only does it protect and look good, but also served as a mounting plate for an AmGood 30" shelf (also Amazon). And it's thick and heavy ! I had to use a tripod to support it during installation. The shelf needed the backsplash because the mounting brackets didn't align with the studs. So I was able to use rivets instead of wallboard anchors because the Broan-NuTone backsplash plate was so thick and solid. Installation was challenging because the stove had to be moved out from the wall. Along with the shelf, it was a 4+ hour project. I don't know EXACTLY how long it took, but it was some time after I went hoarse from all the swearing ...

I feel like this could have been cheaper. It's just a thin sheet of metal you apply to the back oven wall. It's easy to clean and looks industrial. Installation was super simple and it paired well with my Cosmo range hood. It arrived without damage and sits flat against the wall.

Delivery was 5 star (1 day), product is 5 star. The panel is just what I needed as a cabinet shield next to my electric range. Very satisfied with the appearance, cost and installation. The pre-drilled holes made installation very easy. The stainless steel matches the ventilation hood over the stove.

Purchased to keep our backsplash clean. Product arrived well packaged and on time. Easy to clean. Would recommend.

The 1st time, the item was shipped in a huge box but the metal sheet was bended. We thought it can be happened and asked for a replacement. After received the 2nd shipment, once we have pulled the metal sheet out from the packaging, we have immediate found a visible dent. Even Amazon has offered a almost no question asked return policy. But it's a waste of time for us to have the items carried to the post twice.

Es un producto de excelente calidad lo recomiendo!

Nothing to complain about this product! Easy to install, great look as it matches the other appliances, bang for your buck, and how easy to clean and maintain the look!