MG Chemicals 8331D Silver Conductive Epoxy Adhesive, High Conductivity, 20 min Working time, 2-Part, 14 Gram Kit

This is an excellent product. The epoxy cures in about 60 minutes to a nice hard consistency and is very conductive. The small syringes dispense the epoxy very well. I have absolutely no complaints about this produce. That said... I usually just want to use a tiny amount at a time and it's a bit tricky to get a few drops of the A and B parts out of the syringes. I've found that if I twist the plungers as I apply a VERY SMALL amount of force, I can get the small amount out that I want. It'd be nice if this were easier, but I think this is a better solution than having an A and B bottle that I'd have to dip into, so I'm happy... but an easier way to dispense a drop or two would be nice. I haven't check to see if one of my needles can be screwed to the syringes...

I bought the stuff in the auto parts store twice. They restuck my tab, but the defroster never worked. I bought this one, did not use a hair dryer and just let it dry overnight. I didn't even remove my non working tab from the other junk. I just smeared this overtop the tab, making sure the new stuff was contacting the grid. Works perfectly. Yes it's expensive, but not as much as me buying the other stuff twice to have neither attempt to work. This one works. There's enough here to do multiple jobs. Buy this one.

Excellent product

I've no doubt this is an excellent product for typical PC board trace repair or other ordinary connections in high impedance circuits. Unfortunately, it didn't work for me when I tried to repair an open connection on a heated stylus writing arm for an old thermal printer. The stylus should have had about 1.5 to 2 ohms resistance to get hot enough to work on the thermal paper but it ended up with about 9 ohms after I glued the open joint back together. That was enough to kill the project. Not the glue's fault, certainly, just not right for my application. The only issue beyond that was I typically could not work with the mixed glue past the 10 minute mark so, unless I got an old batch, I would recommend you work fast and ignore the stated 20 minute working time.

This is a decent product, and if you really need it, then you won't care about the cost! But please note that the syringe is only 2 inches long---- a very small amount of epoxy ----NOT like the volume you are familiar with Loctite epoxies. So this is good, but VERY expensive for what you get. If you have a small circuit board application, then it's worth it, but if something bigger, then it's way too expensive to get just a few connections for $88. I wish there was a bulk product like this somewhere---- but NOT for hundreds of dollars!

Reattached metal contact posts to the rear window circuit for the third brake light plug. It’s almost like a thick paint before it sets up. Working in a tight space might be messy unless you use something like a paint brush or toothpick to apply it. Sets up quickly in warm conditions.

My rear window defogger had a broken connector tab. I rebonded it with this adhesive. The connection was mechanically sound, and the conductivity of the joint was comparable to the factory joint. $50, wow - expensive. But less than a new window! Also, the kit has enough epoxy to fix over a dozen windows...

Jeep Wrangler JL rear defroster wire has come loose a handful of times and each time has been "repaired" by the dealership. Tired of having to spend hours coordinating the process I decided to buy this and do it myself. It worked great and there is enough to repeat the (inevitable) process at least 5-10 times.

Didn't know this existed but I do now.. easy to use and is a really good conductor. I'm using for a serious precision job and having no problems at all.. shame it's so expensive but sometimes you only get what you pay for .. to be fair a little bit goes a long way. Love the stuff

Sono riuscito a riparlare lo sbrinatore del lunotto termico dell'auto, si era staccato lo spinotto del collegamento elettrico sul vetro. Vi consiglio: pulire bene con alcol, mettere un poco di colla sul vetro dove si è staccato, mettere un poco sullo spinotto e attaccare provvisoriamente con nastro di carta. fermo per un'ora.

This worked perfectly on by 2015 Jeep Wrangler rear window. Reattached the defroster wire and kept the circuit working again!...👍

Me funcionó excelente para arreglar un conector de mi auto

I used the products low resistance to fix a LFP battery terminal that broke off. Then I stabilized it more with another epoxy. The measured ressisance is almost zero.