One enjoy Graphics Card GPU Brace Support, Video Card Sag Holder Bracket, GPU Stand, Anodized Aerospace Aluminum (Black)

Really nice solid sturdy and tall brace! After 3 years of my 3070ti being in and doing a full clean of the case yesterday I noticed my gpu was actually sagging when it didn't before when i last did it, so i needed a brace, I ordered this promptly while on my phone cleaning the case out and had no idea if it was tall enough for the very large gap that it had to accomodate and i'm very happy to report that it's more than adequate there is over 6mm of adjustment on the shaft left for me to use. The rubber grip on the brace head isn't straight nor does it cover the entire head, and the rubber grip on the base is a circle instead of being a rounded square to cover the entire base, however it works just fine, it's not the strongest magnet in the base but it does magnetise and stay in place. I'm very happy with my purchase and it blends in really nicely with my case aesthetics.

Great little stand, i was worried it wouldn't reach the top pcie slot because of how tall my case is but it does the job perfectly.

Feels sturdy and adjustable enough to fit properly. Helps take weight off the GPU and improves peace of mind. I use it for a monitor so it works.

I don't normally review products. Gpu support is well made, sturdy but is far too short for a full tower case like the Corsair 780T which I have. I've ended up having to put 2 idens below it to make up the half inch gap so that it can reach the underside of my new 3080ti. I do not recall seeing a dimension for the length on the listing or reviews

Perfectly serves a purpose for my RTX 3090. My honest recommendation. If you transfer the PC Case (rig), be mindful that it may move or slip, as it is not designed to secure the transport.

Works as expected, stable, easy to customise the height Useful when the distance between your gpu and the nearest flat surface is pretty far away

It's ok, it does the job but the magnet is too weak and does little to hold it in place especially when you are adjusting the height of the bracket. Having 3 hands here would help.

Due to having a saggy graphics card (three fan 3060ti), thought it would be a good idea to make sure that it can sit still in my case. Upon searching for the most viable, I found this GPU Brace Support, and after tightening a few pieces it fitted together really easily. And its magnetic bottom and support rod really help the graphics card to stay in its designated seat on the motherboard, preventing any wobbling and damage to the motherboard. The design is simple and quite atheistic, really makes my PC feel a lot sturdier!

Cumple su función de 10 y tiene muy buena calidad. Tengo una Msi 3070 Gaming X trio que pena 1.64kg y con este soporte la gráfica está ahora bien apoyada y no sufre ni el pci ni la gráfica. Todo un acierto y recomendado. Además me gusta mucho como queda.

Was debating between this one and the one that looks like a nut and bolt. Unfortunately, my case has a cutout on the power supply shroud, for the underside hard drive mounting bracket, right where I need to put the brace. This one has a foot that spans the slot so it works great in my case. It is well made, sturdy and finished like the inside of my case, so it looks like it was made for it. I like the magnet and the rubber pads for both the bottom and the GPU support arm. This minimizes any noise that might arise from vibrations caused by the GPU fans. I only have a RTX 3070 but it has a pretty big heat sink which causes over half a centimeter of sag. The support corrects this no problem and looks great.

If you have a large GPU (3 fans), it starts to bend, which isn't good for the PCIe. This product solves that issue.

Ce support de carte graphique est de très bonne facture, c'est pourquoi je lui mets 5 étoiles. Attention tout de même, le socle est aimanté, oui, mais l'aimantation est vraiment légère ! C'est juste une nappe aimantée assez fine, qui se trouve sous le socle. Ce n'est pas un problème si la vitre de votre boitier peut s'ouvrir n'importe quand ( comme un frigo ), mais ça peut poser problème si, comme moi, votre boitier nécessite d'être couché, afin de l'ouvrir, et que vous devez donc poser le support à l'horizontale dans un premier temps, avant de revisser la vitre et de redresser le PC. Je vous rassure, c'est faisable tout de même, car une fois que vous aurez bien réglé la cale sur le support qui se place sous la carte graphique, ça tiendra, le temps de revisser la vitre et de redresser le PC, à condition de ne pas non-plus vous amuser à secouer votre boitier. Mais attention à ne pas faire tomber le support sur votre carte mère pendant l'opération. J'ai hésité à retirer une étoile pour cette aimantation qui est vraiment un peu trop légère... Mais bon. Je laisse 5 étoiles parce qu'encore une fois, le produit est vraiment de bonne facture, c'est en alu, c'est classe, ça soutient bien la carte graphique une fois en place, et je trouve que le support carré, est plus beau que les autres modèles avec un support rond. Ça aurait quand-même été bien d'avoir un aimant plus puissant, c'est un peu dommage. Ça reste un bon produit ! J'en suis content, une fois en place, c'est top.

Questa staffa è semplicemente perfetta! Arriva in una confezione che sembra quasi un giocattolo, facilissima da montare. Leggera ma nello stesso tempo robusta. l'ho acquistata per la mia rtx4080 gigabyte gaming oc. Sostiene il peso a occhi chiusi, la parte di supporto della staffa è magnetica e con un pad grip di sotto, la staffa si adatta dalle schede in verticale a quelle posizionate in orizzontale. La regolazione della staffa è davvero semplice! E come detto prima, il supporto è magnifico! Assolutamente consigliata! Pro: -Facile da installare -Base magnetica -leggera ma robusta! -Range di regolazione PERFETTO! -Adattabile a mount orizontali e verticali Contro : -Niente led! per chi li vuole