ANYCUBIC Wash and Cure 3 with Gooseneck Lights

Over all, this is a very good product. However, to cut to the chase, I prefer using an ultrasonic cleaner and a homemade UV curing chamber. Here are a few of the pros, cons, and reasons to back up my preferences. Pros: Simplicity (Two machines in one) Pretty good at washing parts (reason for "Pretty good" explained later) Amazing at curing parts (the UV LEDs are super powerful) Attention to safety (the lid is UV blocking and there is a safety switch that shuts down the machine if the lid is removed) Simple user interface Works with a pretty small amount of cleaning fluid (there is an included bracket that lowers the bed to the surface of the liquid) Cons: Price (see below for further detail) Can't use both the cleaning and curing features simultaneously In all, this is a very useful piece of equipment. However, let's go into further detail on a couple of the points made above. Let's start with my comment that it does a "Pretty good" job at cleaning. Though the cleaning system does a surprisingly decent job at removing excess resin from the surface of the prints, it lacks the penetrating capability of an ultrasonic cleaner. With an ultrasonic cleaner, the part gets cleaned inside and out. This is important because resin printers can't really print infill. This means that either you print with 100% infill (i.e. solid) or no infill (i.e. hollow). Because the ultrasonic cleaner uses, well, ultrasonic waves to clean, these waves can penetrate the walls of the print and clean the inside as well. And finally, let's talk price. Though this machine is pretty good at what it does, I don't think it is worth the $150 price tag (as is the price at the time of the writing of this review). I say this because of the all the other methods of doing the things this machine does (sometimes even better) but at a cheaper price. For example, I can get an ultrasonic cleaner (big enough to put the entire build plate into) for around $80 and a string of UV LEDs for $10. So, with a little DIY (to build the curing chamber) I can have equivalent capability for $60 less. In conclusion, this is an all around good machine. I believe that you can make something better, but, since this is the only all-in-one cure/wash station I can find, I would recommend it to anybody that doesn't want to mess with the DIY side.

So recently I took the plunge on my first resin printer experience. I had a small background in FDM printers but was looking for higher definition with my prints. After some research I kept hearing about Anycubic being a big contender in the SLA space. I ended up purchasing the Mono X and the wash and cure station as well. The package showed up and upon opening it I first noticed how well the machines were packed. Everything came in perfect condition. The instructions were clear, bright, and very easy to understand. Both wash and cure station and the printer were both set up within a matter of minutes. I followed the instruction and I ready for my first test print. The print went flawlessly. It was a really great first experience in SLA. The test came out in a few hours and I immediately took advantage of the wash station. This was quickly and obviously money well spent. The print came out clean in just a few minutes and after a few more min of curing I was done. I couldn’t believe how simple it really was. The following day I decided to put the printer to the rest. I printed a full build plate of a highly detailed model and was blown away but how well the mono 4k screen captured the details. As a full time artist this new tool will change everything and will be instrumental in bringing my digital sculptures to life! I plan on doing a full and immersive review of both machines on my YouTube Channel which can be found at BogleArts on YT. I’m attaching pics of my printer set up, the prints I’ve made so far, and some tools I found to help make printing a little easier. The customer service with Anycubic also deserves to be mentioned. Between the customer service and the Mono X community online this is a particularly great printer choice for anyone looking to get into SLA printer to ready to step it up from a small printer to A medium sized machine with a 4k Mono Screen. I plan on updating this review every few months to keep others informed on my printing journey. Stay tuned.

I used to manually clean my resin prints in a plastic tub with alcohol and a toothbrush and cure them under a makeshift nail curing station. Needless to say it was a bit of a headache. Alcohol would spill all over the place and I'd constantly get it on my clothes, etc. With the new ANYCUBIC station, All I have to do is mount the build plate to the metal holder, drop it in the included plastic bin, set the timer and I'm free to walk away and do something else. The built in agitator does a good job of scouring the print and as a bonus cleans the build plate. I still give the print a once over with a brush for good measure but the cleaning process is vastly streamlined. Similarly, the curing process is very easy. Swap out the cleaning tank for the clear turntable base, set the timer and walk away. The direct lights from the side give me a little more confidence the print is getting good even exposure than the top down I was getting from my nail curing station. I'm also a little more trusting the UV light is in the correct spectrum than some of the nail curing stations. Things that could be improved: I wish it would default to wash mode instead of cure when you turn the machine on. I accidentally ran the cure mode and even though I caught it right away it was enough to cure some residual resin on the top of my build plate. Also it would be nice if the cure table had a small lip around the outside. I've had some prints walk off the edge while it was rotating during the cure. Long story short - Do not hesitate to buy this machine. So much easier and cleaner and convenient. It makes resin printing less of a chore.

I expected this device to be a positive improvement for my 3d printing, but I hadn't anticipated the kind of difference it would make. Like most people I saw this device, thought "Eh, kind of interesting, but it just does things I already have a set up for." Eventually though I was convinced to take a chance on it (being stuck at home for the coronavirus social distancing/quarantining certainly helped since I was doing more printing as a result). I was quite surprised. First, it was a big space saver. My old set up was a tupperware of IPA for initial wash, an ultrasonic cleaner for a second rinsing, and then a 5 gallon bucket lined with UV leds with a solar powered rotating display stand. This device replaced all of that and it left me with a lot of space. That extra space has also helped me keep the work area cleaner. Second, it's really convenient. The alternate means of immersing the prints, the wide platform for curing, and plenty of other little things show that this is a device that some thought went into. It's well designed and it does its jobs well. It's hard to point to a single thing, but it definitely makes what is often the most tedious parts of resin printing faster and more enjoyable. The only thing I would put as a warning - the manual doesn't say this (at least not anywhere I saw), but none of the functions work without the protective cover on. This makes sense for the cure mode, but was very confusing when I was attempting to clean some prints the first time. I nearly thought the machine was broken until I tried putting the cover on to see if that made a difference (after at least 15 minutes of trying it in every other possible configuration and with multiple different outlets). If you can spare the funds and are thinking about this device, I strongly recommend making the purchase.

It's okay. A lot less messy/smelly than my old setup of a mason jar for cleaning and an open air uv light hanging on some Paracord above a solar powered spin platform. I think it's overpriced for what it is, and the bucket is a quite a bit bigger than what I need (which means I go through more ISO now) but still a nice addition to my print lab and looks nice. Also makes cool beeping sounds.

I was apprehensive about getting into resin printing because of the washing and curing process involved. I decided st first to build my own curing chamber, but it was hassle and took up a lot of space, especially when I also had a lot of containers for washing. This was the perfect solution for me because of how little space it takes up. It was super easy to use, and included a bunch if extras for different washing situations. It feels really solid and well built too. Makes me feel like a scientist using it haha. Anyways, having had my own jomemade setup and then switching to this was like night and day. It cut down on the time it took to do the entire process significantly and helped me focus on learning the ins and outs of preparing models for print in the chitubox slicer. I cant reccomend this enoug for beginners and experts alike because of the ease of use and effectiveness in both washing and curing. I use this for my photon S, and with a part I printed off thingiverse I was also able to easily mount thebrule plate from the elegoo mars as well. So even if you dont have a photon, it's very possible to take advantage of the washing on the plate feature. And for large items, it comes with a basket to hold parts while it washes. Over all cant think of a con for this. Very happy with the purchase.

I bought my printer (Anycubic Photon) and have been printing for a few months now. When researching what I needed for cleaning and post-processing before my purchase, I found number of DIY solutions for washing away resin and curing the final print. Although they worked, they typically took up too much space (one setup for cleaning, another for curing), did a sub-par job, or both. Enter the Wash and Cure Station. It is extremely effective at washing even the deepest books and crannies, and has plenty of room for the Photon's buildplate. The basket is also a handy option for when you have a rather crowded build plate--just pop em off and into the basket to ensure proper flow around the part for cleaning. The cure function works great, and the timed stop allows me to walk away and work on other things. However, the biggest benefit is the machines size. At roughly the same size as the Photon, it does the job of two pieces of DIY setups that are often large and/or clunky. As space is at a premium in my workspace, this was the kicker for me. My work flow has been extremely easy (printer to wash/cure machine) and has cut down not only on the post-processing time, but also cuts down on the number of paper towels needed for each printing run as you don't have to move the print as much. When I bought the machine, my primary concern was the price. However, after having used it, I can say it was well worth the money. It isn't necessary by any means, but it did ease the transition from FDM printing into the world of DLP.

I have been resin printing for about a year and a half. In that time, I have tried my fair share of DIY washing and curing setups. From multiple jars of IPA to UV Lights glued onto containers, or just leaving prints outside in the sun, I’ve tried it all. I recently learned of Anycubic’s Wash and Cure station and decided to give it a try. This machine has definitely streamlined my post-processing. The machine comes with a large container to hold your IPA or other cleaning liquid, and there is an agitator blade in the bottom which is controlled by magnets to ensure a secure, leak-proof containment. You can choose 2, 4 or 6 minute intervals, and half way through the cycle, the agitator blade reverses ensuring flowing cleaner will wash your parts from both directions. The machine comes with 3 ways to submerge your parts. The first is a metal basket which you can put the parts in if you’ve already removed them from the build plate. There are also a fixed and adjustable build plate holder. This allows you to submerge the build plate so it gets cleaned at the same time as the printed part. The build plate holders are designed to fit most resin printer models, though I had to modify the diameter of the metal connector slightly to get it to hold my Elegoo Mars build plate securely. When it’s time to post-cure your parts, there is a clear curing platform that you port into the middle of the machine. After placing the piece on the platform and placing the lid over the machine, you can set it to curing mode and, like the washing mode, choose 2, 4 or 6 minute cure time. Once started, an array of UV lights is activated while the curing platform rotates 360 degrees. This machine makes the post-printing process so much cleaner and easier. No more swirling printed parts around in a jar of IPA with tongs. No more cleaning the build plate or having to use a homemade UV curing box. I would highly recommend this machine for anyone who is into resin printing.

Es bastante útil para las impresiones pequeñas-medianas

Great price and gets the job done.

Buenos productos

Good little machine though when washing prints you can get wee bits of resin or cured resin that get stuck in the impeller, you will hear a clunk sound but luckily the machine kicks it back out and keeps going. The curing part is fine.

funciona muy bien, lo unico que debi comprar la mas grande ya que tengo la ANYCUBIC Photon Mono X 6Ks, y la placa cabe muyyyy apenas dentro del contenedor para lavarla, pero pues lo principal del lavado de piezas funciona bien.