50W 6Ohm LED Load Resistors

They worked exactly like they said they would! LED bulbs act just like normal incandescent bulbs do! *** These get super hot!! Don’t Touch Them With Your Hands or Fingers!! *** Mount them to metal!! Anything else will burn immediately!!!! *** I have them mounted to an aluminum block with large cooling fins (found here on Amazon), works great on my RV.

Shipped very quickly with Prime shipping for free. Items just as described. 4 heat sink resistors with 4 crimp style splices. After researching installation on YouTube I installed the them on a set of after market LED tail lights on a project truck to fix hyper flash. They worked well and are priced very competitively. The only issue to installation is identifying the right wires in the harness. The splices make the connection very easy. Over all good product, good price, fast free shipping, easy installation. What's not to like.

I bought these for my bike to use with my led lights so they worked probably. They work like they should and they solved the problem with hyper flash. Easy to install

These are perfect for my speaker project. They effectively raise the resistance of my 4 ohm speakers to 6 ohms without losing any sound quality! Very impressed!

Installed an Iron Ox flatbed on my 2019 3500HD. After three blinks, serious hyperflash on the blinkers ! Installed one resister on left and one on the right and now all blinkers flash normal again.

Bought these October of 25 and just yesterday had one explode and melt a hole through my tail lights housing. Im am not to sure why it did that due to the fact that all the rest that I have are fine. They where cheap but should not be burning and melting plastic housing.

Very easy to hook up on most blinkers it has 3 wires brown in the middle is not used, so one end of the resistor to the black and the other end to blue yellow or purple whatever the other wires color is very easy on my HHR

Added these to the taillights on a Ford Excursion to use brighter LED bulbs. One of them lasted about 4 days before burning out. Had extras since only 2 were used. So far they are holding out. 25% failure rate

I purchased these 50W 6 Ohm LED Load Resistors (1157) for my 2009 Range Rover to fix the fast blinking issue on my taillights. I originally ordered aftermarket taillights from another source that were supposed to work right out of the box, but unfortunately that wasn’t the case. After spending nearly two months trying to troubleshoot the problem, I finally decided to try these resistors—and they worked perfectly. Installation was straightforward, and they immediately slowed the blinkers down to the correct speed with no issues. If you’re dealing with hyper flashing after installing LED taillights, these are a great and reliable solution. They saved me a lot of frustration and got everything working the way it should. Highly recommend!

These LED Load Resistors, do get really hot. DO NOT INSTALL them on plastic or near wiring. Simply screw them onto a metal part of the car, away from plastic and wiring. I have a 2017 Jeep Compass. For the front I just used a self tapping screw onto the side of inside of the engine bay. For the rear, since I had no real room to install them on metal, I just left them dangling away from wires. So that way the air cooled them, and after 6 months, no issues. The one time I did have an issue, was when my front right started hyper flashing. So I took a look, the bulb was fine, but the resistor connection had gotten contamination from dirt and water. So I redid that, and no issues at all since then. I just hate how people gve a one star because they get hot. Well duh, what do you expect, its a resistor.

Mais devient chaud.. installer dans un endroit libre, mais pas collé sur un fil..

I had very short wiring on my rear turning lights. The first time I've ever worked on wiring. Bought a multimeter to double check. I was using the right wire. How to buy a fine screwdriver to put in the batteries! What product works as advertise. Don't forget to attach it to metal!

There resistors. They resist. I put them on my LED Tail light upgrade and all is well after 3 months.