BOSCH RA1054 Deluxe Router Guide

I was able to use this on my Milwaukee D handle router with a little modification. I had to buy a 1/4” steel rod, cut it down and use it on the inside set screw holes. It works well. The skid base does interfere with the skid plates on the guide, but I am able to take the skid plates off and use it that way if I need to cut close to the blade. Adding a slight offset to the rods will fix this clearance issue. Overall I like this jig. I’ve used the centering pin by taping it down to the material. The notches in the pin plate are handy for getting it exactly where I need it at. I do wish the tolerance of the pin and the hole were tighter, there’s a little much slack for my liking. It is well built, but using the 1/4” rod isn’t as strong as the 3/8 that came with it. That isn’t an issue with this though, that’s a Milwaukee issue for designing their router for smaller rods.

It's been about two years that I've owned those contraption LOL....it definitely does a lot. The edge guide is real handy, be mindful of adjusting to black plastic "shoes" as far away from center as you can. That gives more riding surface. I own a Bosch dust extractor so it hooks right up, so that was nice. And it definitely helps but in my experience you always end up sweeping up some sawdust. I'm also running the Bosch 1617 series router, again this mates up no issues. The mirco adjust is cool although I can remember which way I'm adjusting so maybe it's not as convenient or maybe I should write on my jig with a sharpie!! It works really well for a circle router guide too. I just recently did an address sign for our house and once I found the little clear center pin every went really smooth. Take light passes, if you're in a hurry wait to work on your project later when you can pay attention. I'd definitely recommend this little gizmo, definitely doesn't store very easy, I hang mine out of harms way.

**Update March 2020** Still a great concept, though I would exercise caution tensioning down the retaining bolts to secure the adjustment rods to your router base. When setting up for a set of cuts for loose mortises The thin metal of my 1617EVS Router's Plunge Base (Bosch Part No. RA1166) cracked, causing there to be a bit of play in the tension. More of a review of the plunge base's poor casting quality rather than the edge guide. Just a "user beware" caution. Still a well thought out accessory. It is often said there is always a right tool for the job. In this case, this is a right tool for many jobs, from cutting circles to routing along an edge. I picked this up for carving out some loose mortises on a furniture project I built and found it worked perfect for the job at hand and even served me well with some rabbeting work I had to knock out without a dedicated bit. I did have some issues balancing the router (a large 1617EVS) on some of my 3/4" stock however, as the edge guide stands proud of the stock by about a quarter of an inch. Not a deal breaker, but something to note if you are going to clamp your workpiece to the bench. If the stock isn't thick enough you'll have to overhang your bench or use supports to lift the workpiece up, so that is something to note. All in all, I really liked the piece for the job it does very very well. It is a great addition to the shop. If you have a Bosch Router and you are looking to do some rabbeting work and/or loose mortise and tenon projects (a la Festool Domino), pick this guy up and with some careful layout it will be a definite asset to the shop.

As described. It fits my Bosch router just like you would expect. it is easy to adjust and stays where it is set at.

If you have the need to operate your router along the edge of a work piece making a dead straight groove, dado or even edge profile, this unit is for you. It is made from quality components in a quality manner. You can adjust the edge guide in the most minute amount possible. I purchased this to use in conjunction with my Bosch 1617, and have used it in the manners above, as well as to make circular cuts. Yes, it will even assist you in making circle cuts and profiles. This also contains fittings to use with dust collection operations to keep your work site clean as well. It installs on the router quickly and easily. Simply loosen set screws on base, insert rods into slots in base, and retighten screws/wingnuts. After that it is a matter of adjusting fence to position bit edge where desired. I would suggest starting on a scrap piece so any even microscopic adjustments, which are easily made with unit, can be made prior to routing final work piece. In the case of edge profiles, you could just as easily 'sneak up' on them instead. All in all this is a very well made tool that serves its intended use very well and I recommend it.

This edge guide works great. I saw so many reviews about people complaining about the circle cutting feature with the “suction cup” center pin. But instead of taping or glueing that suction cup down, I just pushed the center pin through the bottom, and now I can drill a shallow 1/4” center hole and have the pin sit down into it to keep it from moving. It took me 15 seconds to do and it works great. Highly recommend doing it. And if you ever need to switch it back for a project that you can’t drill into, then you can just push the pin back up and use it the way it came. But using it this way is the way to go. You can always just plug the hole after if needed. It will be on the bottom of your workpiece, so no one will ever even see the plug.

I am new to woodworking and am rebuilding my filing cabinet drawers. The dado for the bottom plywood looked complicated but I tested it on a scrap piece of wood to dial it in. Came out good.

great tool

déçu, mauvais matériel, valable uniquement pour défonceuse Bosch que je n'ai pas, je préfère d'autre marques et j'en ai 2 en défonceuse !....

Funktioniert Perfekt kann als parallelanschlag und kreischender verwendet werden. Die zentrierscheibe sollte zum kreisschneiden sehr gut fixiert werden!

Excelente producto, cumple su funcion

Does everything expected plus the radius attachment is a handy bonus!

On peut tout faire avec cette chose. Je l'adore