DRIFT MANIAC 7 Speed Freewheel for E-Bike 11-28T/11-34T Screw On Freewheel

Have a Cyrusher Kommoda Ebike.The stock cassette made for some fast pedaling . Too fast for the ground speed of the bike. Not much resistance.Installed this cassette and wow what a change.Completely transformed the bike to a solid performer . Literally you saved the purchase of that bike.Easy install with the cassette toolSolid product would buy again.Hope this helps someone.

Wanted to eliminate "ghost pedaling" (a/k/a hamster pedaling) in the upper gears of my e-bike (Bee Cool Explorer). This was a fairly easy upgrade, the hardest part is removing the old freewheel (you need the special freewheel tool and a long breaker bar attached to it). Once this new piece installed, I indexed my derailer to the new freewheel (there are dozens of you tube videos showing how easy this is) and then re-lubed my chain. I was quite impressed with how well my chain meshed with the teeth of this freewheel and how smoothly she shifted.I've eliminated the hamster effect of pedaling at higher speeds with no effect (akin to pedaling when you're going downhill). I will say that even in the mid-ranges, I feel more leg muscles working too, an added benefit for my old bones! I opted for staying with the 28T large gear and not going for the 32T or 34T. I live in Florida and we just don't have the kind of hills to need super-low gearing, otherwise I would have gone for it.

Working perfectly on my Engwe L20 2.0. The stock gears only went to 14 teeth. I can comfortably pedal @ 20 mph now.

Great for ebikes. Lots of power to the pedals, much less ghost pedaling.Installation takes custom tools.It's well worth the it if you don't mind modifying a rear cassette removal tool

I have used this seven speed 11-28T freewheel to replace the 14-28T Shimano freewheel on a couple of e-bikes. I wish that e-bike manufacturers would use a 11-28T freewheel as standard equipment. With the replacement I enjoy a slower cadence in 6th and 7th gears and can go up to 27% faster. Well worth the cost and effort in replacing the freewheel. Note that the shifter cable will need to be adjusted at the derailer by turning the knob CCW once the freewheel has been swapped. Recommended.

The tool that came with it was cheap but it did work. It did what it was supposed to do I can now pedal at 25 miles an hour which I couldn’t with the original. I don’t know why they don’t put these on factory.

Perfect upgrade for a 7 speed freewheel for any geared motor ebike This thing combined with the 52 tooth front chainring on my ebike lets me pedal at a steady 37 mph and still feel resistance in the pedals in 7th gear it could even go faster if I could pedal faster, even the lower gears are improved 6th is good for 30+ mph, 5th for 25, 4th for 19 all actually letting me put in effort at various pedal assist levels for example pas 3 on my bike cuts off at 24 mph 5th gear lets me pedal at 25... so the motor only kicks in if i drop below 24. improving efficiency. it's even better at lower gears and settings because the motor uses less wattage when it is needed.

I bought this freewheel almost two years ago and remember how frustrated I was because I had spent a lot of time and simply could not get the 11 teeth sprocket work without slipping. I kind of stopped using the bike for a good year year because of that but recently started over and even bought a new chain (the old one was not worn) and still no success. First of all, as shown in other reviews, the teeth are oddly shaped and partially almost completely missing. That is the case even on the 11 and 13 teeth sprockets, even though it is clear that for these the entire chain tension is carried by only maybe 7 teeth, and yet they still put in these stupid rounded and way too short teeth. Now after replacing the chain (and the old one had accumulated a bit of dirt on the grease) I can clearly see to the side of the 11 teeth sprocket that the chain was in fact running on the freewheel shaft, instead of on the 11 teeth sprocket itself, I can clearly see the grease spots from the chain on the shaft, and the wear. Again, the brand new chain did not help here, it maybe made is worse, as it seems to slip even more. Overall, this is just a stupid design. It is possible that 11 teeth sprockets can work, if the freewheel shaft is smaller in diameter, or if there's normally shaped teeth, but the way they sold this, it just cannot work properly - by design!