ZOSKAY 35kg high Torque Coreless Motor servo Metal Gear Digital and Stainless Steel Gear servo arduino servo for Robotic DIY,RC car (Blue/35KG 180 Degree)

Nice servo for the money, very powerful and fast enough for bashing. Fit well in my 3s BLX Granite. I smashing into a trampoline while doing a backflip and stripped the front diff, but the servo kept going. Stripped two other diffs, but the servo kept going. Accidentally submerged most of the way in a big puddle for 5 seconds, but the servo kept going. A little on the pricey side for a "cheap" servo, but works amazing. Would highly recomend.

Replaced the steering servos in two of my models. The servo in our original E-Maxx 3906 finally have out after 18 years. This servo dropped right in and hooked right up to the Traxxas servo saver. Literally 10 minute replacement. No issues rotating the larger aftermarket wheels on E-maxx. Also installed on brand new Redcat Shredder as we also installed oversize wheels and tires. Easily handles rotating the wheels at standstill. Way more power than the stock servo. No humming, no erratic idling. Bang for the buck upgrade, no reason not to upgrade to this servo. Fast and accurate. Goes right back to center. Will purchase again for other models I purchase in the future.

Purchased for a TRX4 Sport to replace a burned up servo. This servo was smoother, quieter, and as expected much stronger than the 20kg DS3218 it replaced. Installed with no issue using the stock metal servo horn which had a very good spline fit. Servo lead is just the right length to tuck the extra in the radio box. Running it on a Hobbywing 1060 which outputs at 6V. It centers just fine with no buzzing, twitching, or other undesirable noises. Plenty strong enough to turn and return to center under the weight of the truck. Already put a pack on it and it’s strong and fast enough for my TRX4 Sport that is mostly stock other than SSD portal weights on front and MIP driveshafts. Overall very happy with the performance and initial quality at this price for a trail truck. Will update if any issues arise.

Im happy with it. The install is smooth. It’s better than stock. Iv heard people say it will be a little laggy. But I only seem to notice it when you first start the car. Maybe just let it warm up a lil bit. Another friend says he’s had his in for almost 5 years. So I do believe it’s durable. Going strong so far. If you’re balling on a budget. I’d go for it.

Way better than traxxas servos, even the 2075r. Save money and get this instead its much more responsive and quick. I did crash at 60mph and the servo is constantly spinning now but i just ordered another one, still cheaper than traxxas oem.

This servo works well in my Clodbuster. Its a little slow but it has enough torque to handle the 4 wheel steering needs of the truck and the Clod has huge tires so I'm impressed. Would buy again if I needed a cheap monster truck steering servo.

I have been in the RC hobby world for just over a year. I belong to many RC forums and FB groups for different models. Lots of people aske what Servo they should get and then 100 different people give their opinions. There are tons of people recommending the very high end(and expensive) servos. They say pay once and cry ones. Normally I agree with them. If I used my RC more and absolute needed it to be bullet proof and perform without any chance of failure I would spend the money. Unfortunately I don't have the time to devote to the hobby. I want something inexpensive and decent quality. If it fails I will just stop playing with my RC and buy another one.

You pay for what you get. Have 3 of these. Unless you have a BEC voltage of 7.4v, you will not get the full 35KG torque. 6v BEC from a RTR ESC which is pretty much standard on 99% of RTR stock config will ONLY give you 32kg. Food for thought when deciding. Also it is strong enough... But Slow, which is not a great problem for most Basher RC rigs. Just understand that before deciding to purchase. I always take my supposedly waterproof resistant servos apart and to check and see. -What I see is that the top unshielded ball bearing has an o-ring on top. It is the wrong size and much too large. When I took it apart it was obvious that the ball bearing was locked due to this wrong over sized o-ring. I have see this on just about every cheap made in China servo. Have tried more than a dozen. I remove the o-ring and place it outside over the expose servo spline, under the servo arm during reassembly. I put some silicone grease under the 0-ring for water proofing. Now the servo will be smoother and much faster. - I see that the circuit board is NOT waterproofed with a silicone modified coating which ALL name brand servos have. This is a prerequisite for any waterproofed spec'd servo IMHO. Water will migrate into the servo case, so this circuit board WILL corrode if you don't use any readily available Silicone Modified Coating on it while it is apart. I do this to all the cheap China servos. - The gears are not lubed properly. A generous amount of grease is in there..... however that grease is not n the teeth of any of the gears. So the blob of grease installed during mfr, does nothing for the lubrication of all the gears. They are essentially dry. Poor quality control. I imagine to get the price point where it is. These are relabeled servos that come with many different labels from other sellers. All in all, for the price and IF you modd the servo like I do, it will serve well. If you don't, you will be replacing it more often than if you buy a known brand servo like Hitec, Savox or Futaba which cost twice as much. If you address the flaws that I stated above, right away, out the box, it is a decent cheap alternative. I will follow up and may post pictures of how I mod this servo. I have 3 so far. I treat all new servos the same. Whether name brand or not. Even my 2 Savox 1210's are noisey and horrible at times. So cheaper alternatives are here, although far from perfect. This 35kg servo must be examined and modded to last any decent amount of time. Beware of this. Been in the hobby for 35 years and dozens of servos later this is what I have learned regarding servos. EDIT: I have total of 5 now. They are great for the price and I must say that NONE have failed me yet. As this servo wears even with carefull greasing of all the teeth, slop will develope. But it is still strong and potentiometer centers it well. Quiet when idle. Beats any Savox hands down. There is grease on the gears however its just one blob of grease that nowhere touches the gears teeth. so the gears are dry as a bone. Easy fix. The 180 degree servo is NOT 180 . It is 120 degrees. All of my 180's are only 120 degree sweep. Not an issue for me though. Just be advised of this. The O-Rings are still crushing the top ball bearing and the BB is locked. I still remove the O-ring and just plact over the out put spline before installing the servo arm on. I use these on my Crawler and all my Arrma 6S rigs incuding my 1/7 scale Mojave and Limitless. Infraction. For the price it can't be beat. But, this is not a Racing Class servo. Be advised. But I feel it ranks with Savox and perhaps better. Savox are rebuildable, These are throwaways at a low price. And again I must say, Everyone is working fine. And I abuse these servos.

Superb quality. Love it. Amazon send it fast. Amazing

クローラで使って動作は問題ありません。 動作音は煩わしいレベルで気になると言えば気になります。

this is a great product

My steering servo was weak. Maybe tired. I replaced with the 35kg servo and now, WOW! If the truck is leaning, it’ll lift the entire thing when I turn. If a tire is wedged on a rock, it’ll move the rock or slide the front end when I turn. Huge improvement on maneuverability and turning speed. Great upgrade for the price!

I have two of these and they are plenty strong and fast for general use. One on a 1/7 Mojave EXB and one on an SCX10.3. Have had one for over a year with no issues and just picked up the second one. Great value and much better than the all plastic servos that comes with most RTR's (and this one is cheaper to buy vs replacing the OEM RTR ones).