33FT

If you've used 3M VHB tape you know it works great. I've used it for everything from fish tank sumps to automobile spoilers and trim. This time it was to replace the knock-off double sided tape that came on my upper roof spoiler for my car. The key for this tape is to use it on non-porous material like glass, gloss auto paint (not household wall paint), metal etc. Make sure to prep the surface and do a final clean wipe and dry with alcohol before applying the tape. This stuff holds incredibly well if you do your part to prepare the surface. On my previous cars I've used it for trunk lip spoilers for over 10 years and it holds up to the weather and abuse. never failed or peels. Its my go to tape for such applications. Its not meant to be easy to remove. I bought the 0.4" width in this listing as there are 2 strips down my spoiler. one strip is .4" and the other is .5" I'm glad they sell many different sizes.

I bought this for a LED project in a outdoor gazebo. I used it to replace the doublesided tape that came with the waterprrof LED light strip that I purchased. I am glad I did. The light have been stuck up on the metal support braces of my gazebo since early June and so far this tape had held them in place in wind, rain, and heat. No sagging or failures so far. The thin foam cor of the tape is perfect for LED lights. No too thick to make the light looks odd against the surface that they are attached to but no too thin to rip and cause a failure of the adheasion. They are easy to cut and peal to stick. They are forgiving to mistakes as it does nto seem to grab so had that you can not reposition but once you press it into place it holds well. I can not speak as to if it leaves any residue when removed as I have not removed any of the LED strip yet and none of it has failed. This is a must if youo are working with 10MM LED light strip and are planning on useing the double sided tape included with them. I highly recommend useing this tape instead.

I bought this tape to restick some outdoor LED light strips that had gotten unsticky in places. It works exactly as I had hoped. It's thin, fairly easy to apply, and adheres well. The only problem I had at all was the red backing is a bit hard to get a hold of, but once you are able to separate a tiny section, it comes right off. I ended up using my Tweezerman tweezers to grab it, which helped. Update: I'm not changing my rating on this tape, but wanted to come back and leave a cautionary note. While it does adhere very well, as stated above, it it EXTREMELY difficult to remove, which obviously I didn't find out until much later. This could be because I used it outdoors and the heat caused it to stick badly, or it could be that it adheres so well that it's just very difficult to remove, I'm not sure. So just be careful where you use it, and make sure it's not on something that you may want to remove it from later.

Kind of difficult to remove the red strip covering the tape. Once you get it off you can stick tape to most smooth surfaces well. I did need to take off some excess at one point and it was pretty tough after sticking onto a wall. That being said the tape itself worked for my application and held strong.

Good .

The product works great! But I have spent up 15 minutes trying to get the dang red backing off the back! Here is how I do it now and it only takes about ten seconds: - It is best to sit at a desk or at a countertop so you can concentrate and get all the tape pieces done in one easy batch. - Cut off a 1-1/2 piece - Fold it so it is red on both sides and has about 1/4" to 3/8" of adhesive exposed. I call this my "handle" - Cut a piece about 3/4" longer than you need and place on your project. Rub it in well. That's your "Project" piece - Take your "Handle" and stick it to your the extra bit on your "project" piece with about a 1/4" overlap. Squeeze them together tightly so it bonds well. - Now you just pull slightly on your "handle" as you poke under the red edge with a razor knife. you'll find it much easier to separate. - Cut off the project piece at the right length with the razor knife. Leave a "tab" of red backing to later use to get the backing off. - Save the handle for the next tape point on your project. - When you are ready to place your project, it only takes you seconds to pull off all the backing. No flustration, what-so-ever!

I was expecting the traditional 3-M foam douple-sided mounting tape. This is weak and thin tape! I tried to attach a lightweight full length mirror to my wall, and within 2 hours, it fell down and broke!! I also used it to tape up a small tin sign, and that fell and got bent. This tape is costing me money!! It's so thin and flat, I don't see how it could hold anything other than a paper sign. I sure don't see how it could hold rope lights as it's advertised. I bought it based on glowing reviews, but there's just no way this is good tape. My walls are not textured. The surface was not cold. I held the tape in place a while. I think I will be returning this. I'll go to an actual store where I can see what I'm buying.

The hold and thickness was perfect

Worked great! Had a problem with a foot cover on a chair that kept slipping off.

Colle tres bien

Great product. Works well. Used to replace tacky adhesive for door panel moisture barrier.

Très bon ruban double face

Worked perfect to reinstall my ram 1500 stock fender flares