VXB Brand 1000 lbs Capacity 12" Lazy Susan Bearing 5/16 Thick Turntable Bearings Made in USA 1000 lbs. max 15" inch to 30" inch Turntable Diameter Zinc Plated

This product is exactly what it purports to be. It is a low cost 12" diameter Lazy Susan bearing. As such one cannot expect it to perform like a higher quality equivalent will. It is functional and works well. However, as reported by others, it is noisy. So, if your application is to turn your favorite rocker or recliner into a swivel version of same, don't be swiveling back and forth during your favorite TV show. Also, be sure the surfaces you are attaching it to are perfectly flat. If not, you will be warping the bearing as you attach it and then it will not rotate smoothly, if at all. In my project the bearing sits between two pieces of 1/2" plywood and carries a load of perhaps 75 pounds max. In this case it works well, rotates smoothly, and is noisy. Fortunately for me, noise is not an issue. If noise is an issue for your project, you will be better served by searching for a higher quality product.

I put them on two 18" turntables from Amazon (Lipper International 1118 Acacia Wood 18" Lazy Susan Kitchen Turntable). These steel turntables are a huge upgrade to what you would get on any wood turntable unless you pay $70+. You can glue them on or screw them on with short flat head 3/8" long screws, there is an access hole for the screws as you turn it around, next I bought some heavy duty duct tape (like Gorilla tape), cut about 7 strips and trimmed it off clean with a razor blade, but first I sanded the inside metal edge with sandpaper (put gloves on) this removed any of the sharp edges. After finished it is now low-profile, looks much better and works 10 times better compared to what was original installed. With some wood polish you have the best turntable you can ever find!!

I have a large Qidi X-Max3 FDM 3d printer. The filament is mounted on the back and so I wanted a better way to access the rear of the printer without having to bust my back moving it. I made a turntable out of this Lazy Susan and a piece of plywood and bolted it to the bench. The installation was very easy and it does what I want it to do! Highly Recommend!

I bought this bearing turntable to replace the flimsy plastic turntable that originally comes with the revolving CD/DVD tower. In fact, Amazon recommends those buying the tower buy this turntable and I believe they are correct. This bearing turntable works very smoothly with the tower and the weight of the CDs the tower will support. The turntable is easy to install though buyers be advice it does not come with any screws or attachment. And that's the way it should be, since the manufacturer cannot foresee how it will be used. Overall it's a good product.

A solid replacement for the cheap factory original that came with my DVD display case. This item is all-metal construction and features real ball-bearing action. Rated for 1,000 pounds and it feels sturdy enough to not question that claim! Easy enough to install using screws between the upper and lower pieces of the DVD case. Simple directions that were provided by ROBERT FAULKS in an answer above were quite helpful. Might have applied a little lithium grease to quiet the ballbearing sound, but I kind of like it anyway so no harm done. At the price, it is hard for me to imagine a better bargain for a top-quality item. I have included several photos that may help somebody else see how I attached this to the upper and bottom halves using screws. No screws or other mounting hardware is included so a trip to the hardware store for your chosen attachment method is likely required.

Based on reviews, I have an under the counter Lazy Susie that over the years of putting heavy Pyrex dishes on the bottom shelf it was darn near impossible to turn. Took a chance on this product and bingo I hit the jack pot. I installed on the bottom shelf and it works wonderful. Put lots of Dishes and kept putting dishes and it turns so so easy. Did do as several reviews recommend squirt with WD 40 product, actually used Blaster PB -50.... Thanks to all the reviews which helped me decide to do this project. I did buy the 1000 lb capacity because I did not want to do this project again and have a very large capacity product. If I need something like this again for what ever I will be the first to buy. Cheers..

I built this system to help my wife enter the camper from a wheelchair. The Lazy Susan is guided inside a frame of a plywood platform, which is raised to the height of the camper entrance. The Indeelift is sitting on a smaller wooden platform that is bolted to the Lazy Susan. Once she is sitting on the lift, she can raise the electric lift to the waist height with the push of a button. I will then spin her 90 degrees to face the entrance of the camper door. She will be able to stand up and grab onto the handlebars at the door and everywhere inside.

I used this for a lazy susan that was fairly large and heavy, so this fit completely under it and had a wide footprint to make it stable. I wish that the bearing had attached felt on the underside, but I used stick-on rubber pieces instead. The bearing is a bit loud when spinning, so I added some lithium grease to help, but it hasn't taken all of the metallic sound away. It's a sturdy piece so I expect it to last for some time.

Muy buen rodamiento. Ya lo he comprado 3 veces por su buena calidad.

Used this to make a cutting turntable for quilting. Cut a 24" round of mdf, adhered a section of an old cutting mat to that and mounted it on the turntable..This turntable rotates easily and smoothly and has a low profile that is stable enough to be able to cut projects using a rotary cutter without the top tilting.

A First Class Purchase. I would buy again. Now, to make that motorcycle turn-table!

Will do the job well

Nice built, strong, smoothly mooving. Good product.