TOMSIN Joysticks Replacement for PS5 Controller,4 Pack Hall Effect 3D Analog Sensor Joysticks Module with Thumbsticks Cap for Playstation 5 Controller,Thumbsticks Repair Kit for PS5 Controller

This is a great quality kit with enough parts to fix two PS5 controllers with the dreaded drift problems.Regarding the review that said that these drift right out of the box, they very well might. After installation they need to be mechanically adjusted.. Watch some YouTube videos on Installing hall effect joysticks. After install, you need to hook the board up to USB and check the centering with a online gamepad test site. If the sticks need to be centered, you can put the end of the tweezers through the little holes next to the sensors on the stick assembly. And adjust the stick as necessary. It's a little fiddly, but you only have to do it once.They worked perfectly on my gamepad with no jitter after install and one was centered properly right out of the box the other one needed a little adjustment..I would generally recommend this install for somebody confident with electronic repair. There is non-beginner level desoldering to be done and several very delicate ribbon cable that must be removed and replaced.. The solder work can be done with a soldering iron, but will go much quicker with a hot air workstation.Overall, I was very pleased with this kit. It was very complete with not only the Hall Effect sensors, but a properly sized screwdriver and tool to open the case, extra stick covers, Extra screws in case you drop any. If you have the tools, you can repair two Controllers for less than 20 bucks, And the problem will not recur, Or you can give Sony 60 bucks apiece for new Controllers that will start drifting again in a month or six months or a year. Personally, I would rather put a bit of effort into it and be done with the problem.

Good quality joysticks.Just for advice: Desoldering is pretty tough, so you'll need a powerful soldering iron, (400-450C) or a soldering fan. And be carefu with small SMD components.After installation I had to make a calibration, but it's pretty easy, and after that they worked perfectly. Great choice if you want to get rid of stick drift forever.

the product works fantastic. it took a lot of trial and error and new tools ordered but once I got the old joy sticks off these replaced them perfect and are super smooth. I plan on swapping all my PS5 controllers now using these guys. dont want to go back to the terrible old potentiometers.

The sticks work just be careful of the centring of the stick, check it for stiffness the one i soldered in drifts up SLIGHTLY so it's not too bad just set a dead zone of like .10 and its fine. also the stick click is kinda unreliable but not having to replace them will be nice.

I'd say this is a bare minimum upgrade you can do for your controller to get rid of stick drift. While not as robust as other hall-effect kits that come with calibration boards, these will get the job done with proper mechanical calibration by adjusting the magnet position, and fine-tuning through software calibration using dualsense-tools on github. If you set everything right the first time with only these joysticks, then there should be no need to do it again later on.I recommend buying a 4-pack for each controller you plan to modify because there might be some quality control issues with the joysticks themselves. Some might physically be more centered than others. Be sure to examine the alignment of the joystick before installing it. I made the mistake of soldering everything in only to realize one joystick tilted up and the other tilted a bit down. While it still functioned properly, it was a bit of an eye sore. Fortunately, the last two were perfectly even.Since I ended up using all four joysticks during the process, I found circularity to be inconsistent between the first two and the last two I installed. For the first two, circularity was a little over 14% error. The left stick had a bottom corner bias and the right stick had a top corner bias. It is possible that this was because of the tilted resting positions for each stick. Fortunately, the last two joysticks gave me the best circularity at 12% error with almost no corner bias. All four had no problems with being centered at zero.Overall, this was great bundle! The install was a bit of a pain and while I only needed the joysticks, its nice to have the extra thumbstick covers and silicone rings.

This joystick swap requires desoldering and soldering on the Dualsense circuit board. I am NOT very good at soldering, but I was able to complete the project and the results are perfect! You may need to re-calibrate the joysticks after install. I did not, they both zero'd within the default dead-zone, but you may need to calibrate. No big deal.If I can offer any tips on the desoldering aspect of this project, they are these:-clip off the through board wire as close as you can to the board.-gently break off the two potentiometers from each joystick so they are separate from the joystick housing.-At about 400C move between the three through wires for each potentiometer until it drops free. Do that x4 (two for each joystick).-That should give you enough space to clip the through wires and housing connectors on the TOP of the board. That should fully release the old joystick.-Switch to your needle point solder gun bit and reheat.-Push through each connection on the circuit board to extricate the clipped off remnant of the through board wire from the old joystick.-Use solder wick to clean top and bottom circuit board and you're ready for install.-Make sure the new joysticks are seated flush to the board before soldering.Be patient and good luck!

I removed my original joy sticks on my ps5 controller and Install these joy sticks on it. My controller now only go one direction.

Note that these are kind of difficult to install (Sony's fault), and are a little more fragile than the original sticks. But I bought these to fix stick drift and that they did.Note that you need to watch a youtube tutorial to figure out how to calibrate them. It's simple but hard to guess.

Mi control de PS5 tenia un drift terrible en el joystick derecho asi que compre estos, y lo lleve con un técnico a que me lo pusiera, hasta ahorita me ha funcionado muy bien, según con estos joystick de efecto hall se elimina el drift pero creo que no es del todo cierto ya que en warzon cuando habro el mapa el cursos se mueve solo hacia la izquierda pero muy leve, nada que no se pueda solucionar aumentando la zona muerta un poco, lo raro y a la vez bueno es que hasta ahorita ese pequeño drift solo me pasa en warzone ya que juego rainbow six siege y en ese juego no he necesitado mover la zona muerta incluso creo que le baje para ver si hacía lo mismo y no, ahi no se ha movido nada, hasta ahorita estoy satisfecho con la compra, esperaré unos meses para ver que tal va, apenas llevo como 2-3 semanas que me lo repararon y hasta ahorita todo bien.

Something to know in advance is that when you start up your controller the sticks need to be centered or they will zero at the wrong position.Needs direction for calibrating for various controllers. Sensitivity is a wee issue.

Nice so far

Se ven geniales, viene muy completo el paquete

I bought this set hoping to replace my PS5 joysticks, but turns out I didn't have the right skills or tools to for the desoldering required.But apart from that, the "high-quality professional opening tool" in the box is cheap plastic, and broke immediately when using it to open my controller. Had to resort to using a small flat screwdriver. Can't speak to the rest of the parts...