Door Lights Logo Projector Puddle Lights Ultra-Bright Welcome Step Light, Never Fade Tesla Puddle Lights Compatible with Tesla Model 3, S, Y, X Plug & Play (Blue)

Hardest part is removing the plastic cover from the door. Need patience to not break the cover &/or leave scratches on the door. Once removed, it’s easy to unhook the wire harness & replace with the new lights. Very bright & sharp imagery of the Tesla monogram & logo.

The lights look cool, it's much nicer opening the door to see see a blue Tesla Logo being projected on the ground instead of plain light. In my original box 3 of the 4 lights worked. I emailed the address in the package and they sent me a replacement light.Installation is very easy, they even provide the tiny screw driver needed to do the job. The extension cable built on these lights, make them much easier to install compared with to the original Tesla door light.I installed these on a 2024 Tesla Model 3.

My wife wanted to get the red color and I’m glad we did. Wow they look great nice and bright easy to pop in. Took me two minutes to put all four of them in and I’m glad I did. I would definitely recommend this product to anyone out there do not have any hesitations. And I definitely would recommend the upgrade.

Very easy to install. A direct fit install, a simple plug and play. The projection image is very clear and crisp.

Very easy to install. It took me around 10 minutes for all four. A nice bright well defined image. I’m very happy with them.

I replaced the puddle lights in my 2024 Tesla Model 3 Highland, front and back. The kit came with four lights and a small screwdriver / prying tool.Start in the back as the wires are longer and easier to work with. Use the prying tool to remove the old puddle light from the door. I was worried about breaking it but they popped out easily. The tricky part is removing the wire from the old light. Use the same tool to depress a latch on the top side. The wire will then slide out of a socket that is on the old light. The new light comes with a pigtail so you have more wire to work with. Just connect the new light’s pigtail (female) to the car wire (male). Next, stuff the wires up into the door and pop the new light into place. Be sure you have the orientation correct!The fronts are a little harder. It’s the same process, but in my car the wires in the car weren’t as long as the back so it was harder to find the release pin to remove the car wiring from the light. Also, in my car, the lights were held in by friction and by some tape or glue (which might actually be foam soundproofing in the door, it was hard to tell). So, start with the backs then so the fronts.I found it easier to place a towel on the ground and lie on that. I also had a 9 year old helper hand me the replacement lights and hold a flashlight for me so I could see where I was working.The entire project might have taken 20 minutes. I could probably do it all again in 5.As for the quality of the lights, they look great. So far I’m very pleased.

These are easy to install. The red is a nice and bright. Clearly visible Tesla symbol. Just a bit small but overall a great purchase.

The media could not be loaded. I was a little intimidated when buying this because I thought it would be hard to install. Not difficult at all, and it’s such a cool addition. Way cheaper than Tesla’s version, and the image is still crisp and bright. Highly recommend!

Pros:- the puddle lights are beautiful, bright and changes the experience for better in a Tesla.- The installation is not easy but not too difficult as well. The instructions should be re-written to make them better and when possible, be complimented by videos/links to learn the best way without harming the car doors and/or fittings in any way.Cons:- No cons so far; I shall use them and be able to report more once I have used them long enough.- I was not able to use the included pry-tool (basically, a flathead screw-driver) to pry the LED open. So, I have used a larger screw-driver to pry the LED open.- The instructions are not helpful, I broke one of the original LEDs of my Tesla in the process of replacing them. Lucky that they are not needed anymore! You need to follow the two tips mentioned below before proceeding.TIPS:- to open the LEDs successfully, you must start prying them from the sides (the longer sides); not the shorter sides. This makes the releasing much easier and non-destructive.- The cars original LEDs come with very short wires, so you cannot pull them out long enough, The screw driver can be used to detach the cable by flicking the clamp properly.Recommend:I recommend this replacements highly. They improve your experience in a Tesla. You can make other Tesla owners jealous, for sure :))

Lights brightness is low and logo on the floor bigger than shouldn't be, so return it, costs me the postage.

installé les 4 en 5 min attention au sens mes jolie quand on ouvre les porte ca fini l esthétique ++++++

Well made product , I am sure will last many years, Tesla name . Projects clear and sharp . All you need is in pack .no need to cut any wires everything is plug in and you are done ✔️

Great product.