DIY-MotoShield Pro Premium Precut Ceramic Window Tint for 4-Door Trucks - All Windows [99% Infrared Heat Reduction/Blocks 99% UV]

First let me say that this is a great product. Second, let me qualify that by saying the only experience I've had besides this with window film was the film I applied to the windows in my home. So when I decided to tackle this project because the local shop wanted over $500, I based my ability to get it done properly on this limited experience. What I discovered was this: side windows on a normal passenger car are fairly straightforward and it is possible to achieve acceptable results as these windows tend to be flat, vertical and of a manageable size. But the REAR window (on my car, a 2005 Chevy Classic) is tilted back at a 50 degree angle, has imbedded antennae, heating elements, and a field of small raised dots which may be for sun mitigation. The space is cramped, even with the rear shelf and seat removed. Bottom line: I was completely unable to get the film installed in the rear glass. I had watched several hours of Utube videos, and I had an assistant but was completely unprepared for the degree of difficulty there. I don't blame the product, I blame the hubris of the idiot I hired to install the product. The only product fault was that two of the pieces were mislabeled, but that wasn't much of an issue because of the obvious differences in shape. The seller included a practice piece and clear instructions; there were no creases or any defects when the product arrived, it was perfect. If anyone is still thinking of applying their own film, I heartily recommend this product. Just be aware of your own limitations, and be especially sure that you know how to heat shrink the film properly because it is an important step, ESPECIALLY on the rear glass. I think that someone in better shape than I would do a better job, so I'm giving this product 5 stars all around because my side glass turned out well enough that I'm not gonna just have the entire car redone by a shop.

I had to pay over $500 to get these removed and have the shop put better quality ceramic tints on. The tints got extremely foggy in direct sunlight, I waited 3 weeks to a month to see if it would set in and fix itself and it did not. me and my wallet are extremely unhappy with the quality and overall cost to purchase them, and then pay another fee to replace them, UNACCEPTABLE. Would not recommend if you are doing to be putting these on your back and front windshield.

Installed on a 2013 Nissan Versa. Came packaged in a cardboard tube which is good, however, mine had a dent in the side so there were a few imperfections in the roll. I dont think it made a difference. The roll had dust on both ends, so I would recommend that the company place the product in plastic before inserting in the tube for shipping. Looks like a quality product.Dont try to install this without the right tools. I purchased a tint installation kit with different squeegees, plastic tools, razor knife, etc. I purchased a decent heat gun that has 12 temperature settings. Purchased two spray bottles from walmart, one for cleaner the other for slip solution. Slip solution I used was 2 cups distilled water and 1/4 tsp Johnson baby shampoo. Worked very well.Just because its pre cut doesn't mean you wont be cutting. They left an important part out of the video. After you remove the outer tint you then have to cut the clear line away, too. Otherwise you wont be able to place the tint on the outside of the window for the fitting and get it tucked into the moldings. The thing piece will be a little large but will tuck into behind moldings and trim panels.The door windows went in easily, I tried to take my time being careful but still managed to catch a corner with a squeegee folding it back or put a small crease in here or there. You have to press rather firmly to ensure you get all the solution and air out from under the tint.The rear window is where the trouble was. I removed the rear brake light housing and plastic pillar trim panels to allow for easier installation. I watched numerous videos and learned my lesson from the door windows. I didn't think my back glass was that curved but I guess I was wrong.I placed the tint on the rear glass and it did not shrink much. Still had many large fingers in it that I could not get rid of and no matter how slow I went, i still ended up with a few small creases in the tint. I figured I would place it inside the glass and try to shrink it that way.That worked better, however, it was still a lost cause. I ended up ripping it out and throwing it away due to all the fingers I could not shrink up and squeegee out. The only other option I know of is to use strips but you'd have to cut this in order to do that.Not going to attempt to install the windshield's today. Probably going ask a shop if they will install this product and have them do it.

I’m giving this product 5 stars. If you don’t know how to tint windows, don’t buy this tint and then give it a bad review because you didn’t know what you were doing. I bought it because I have experience tinting.That being said, to the people who know how, this is nice tint, does as expected and for a guy that hasn’t tinted a window in about 25 years it was very forgiving. You know the deal, the wetter the better!! I kept it sprayed down and it moved for me with palm taps when needed and responded well to the heat gun, I even had to pull a piece after I had squeegied it out and it laid back down and acted right. (Had a piece of trash that was buggin the piss outta me)The cuts were good but I still had to do a little trimming. I didn’t have a glass rack so I razor scraped the outside to check and trimmed what I needed. Asked for a limo eyebrow and they sent me the whole windshield lol.In short, nothing to fear with this product, well packaged, no damage upon arrival, I’d recommend it or purchase again if I was looking to do another rig.